
1 / 3 · Click to enlarge
AI Summary
A compact AT24C256 breakout that adds 256Kb (32KB) of non-volatile EEPROM storage over a simple two-wire I2C interface. It keeps your settings, calibration data and logs safe after power loss and works with both 3.3V and 5V systems.
Key Highlights
- 256Kb (32KB) non-volatile EEPROM storage in a small breakout board
- Simple I2C interface using only SDA and SCL data lines
- Onboard 10K pull-up resistors for stable bus communication
- Accepts 2.7V to 5.5V, compatible with 3.3V and 5V logic
- Rated for up to 1,000,000 write cycles and over 100 years retention
- Supports 100 kHz standard and 400 kHz fast-mode I2C clocks
Ideal For
- Arduino and microcontroller hobbyists needing extra non-volatile storage
- Students learning I2C memory interfacing
- Makers building IoT nodes that must keep settings after reboot
- Robotics builders storing calibration and configuration data
- Engineers prototyping data logging with a simple two-wire bus
Buying Tip
Check your I2C bus for existing pull-up resistors before adding this board, since its onboard 10K pull-ups sit in parallel with any others on the same lines.
Elecvora expert review
Our verdict
A tidy, low-cost way to add 32KB of non-volatile storage to an I2C project, with useful onboard pull-ups and broad voltage support. It is a sensible choice for settings and calibration storage where a simple two-wire bus is already available.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Generous 32KB capacity for configuration and log data
- Onboard 10K pull-up resistors simplify wiring
- Works across 3.3V and 5V logic systems
- High write endurance and long retention ratings
Cons
- Requires I2C driver support and address management in code
- Onboard pull-ups may need checking if other devices share the bus
- EEPROM writes are slower than RAM, so plan write frequency
Best for
Makers and engineers storing settings, calibration and logs on an I2C bus
Not ideal for
Projects needing high-speed bulk storage or frequent large writes
Specifications
| Shipping Weight | 0.005 kg |
|---|---|
| Shipping Dimensions | 4 × 3 × 2 cm |
What's in the box
- 1 x AT24C256 I2C Interface EEPROM Storage Module
Frequently Asked Questions
What is the storage capacity of this module?
Does it keep data when power is removed?
What voltage does the module need?
How many pins do I need to connect?
Are pull-up resistors included on the board?
What is included in the package?
Overview
The AT24C256 I2C EEPROM Storage Module gives your project a dedicated place to store data that must survive a power cycle. Built around the AT24C256 memory IC, it provides 256 kilobit (32 kilobyte) of non-volatile EEPROM, considerably more than the small EEPROM built into most microcontrollers. Data is read and written over a standard I2C bus, so only two signal lines are needed.
The module is compact at roughly 19 x 11 x 1 mm and weighs about 1 g, making it easy to tuck into an enclosure or solder onto a small carrier board. It is aimed at makers, students and engineers who need dependable storage without adding a larger memory solution.
Key Features
- Non-volatile EEPROM memory that retains data without power
- 256Kb capacity, organised as 32,768 x 8 bits (32KB)
- I2C communication using SCL and SDA
- Built-in 10K pull-up resistors on the I2C lines
- Operating voltage range of 2.7V to 5.5V DC
- Logic compatibility with 3.3V and 5V systems
- I2C clock support for 100 kHz standard and 400 kHz fast mode
- Endurance rated up to 1,000,000 write cycles
- Data retention rated at more than 100 years
Specifications Explained
Capacity: 256Kb equals 32KB, enough for configuration blocks, calibration tables and moderate log files. Interface: I2C keeps wiring simple; connect SCL and SDA plus power and ground. Pull-ups: the onboard 10K resistors help maintain clean bus signals, though you should check your bus for conflicts if other pull-ups are already fitted.
Voltage: the 2.7V to 5.5V range lets the board run from common 3.3V and 5V rails. Speed: 100 kHz standard mode and 400 kHz fast mode cover typical embedded use. Endurance and retention: up to 1,000,000 write cycles and over 100 years of retention make it suitable for long-term storage tasks.
Compatibility and Requirements
The module works with any host that provides an I2C bus and a supply within 2.7V to 5.5V. Because it supports both 3.3V and 5V logic, it can be used across a range of microcontroller platforms. You will need to connect VCC, GND, SDA and SCL, and your project must include I2C driver support for the AT24C256.
Typical Uses
- Saving device settings and user preferences
- Storing calibration values for sensors and instruments
- Logging data in IoT nodes and robotics projects
- Keeping counters or records across power cycles
What's in the Box
1 x AT24C256 I2C Interface EEPROM Storage Module.













