Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

This CP2112 module bridges USB to I2C/SMBus with eight configurable GPIO pins and works as a standard HID device without custom drivers. It is a fast, firmware-free way to debug and control I2C peripherals from a PC.

Key Highlights

  • USB to I2C/SMBus bridge based on the CP2112 controller
  • Eight GPIO pins configurable as input/output and open-drain/push-pull
  • I/O voltage range from 1.8 V up to VDD
  • Standard HID class device works without custom drivers
  • 512-byte SMBus data buffer and configurable clock speed
  • Compact 29.5 mm x 21.3 mm board with two M3 mounting holes

Ideal For

  • Embedded engineers debugging I2C buses
  • Makers integrating I2C sensors with a PC
  • Test technicians automating GPIO control
  • Students learning I2C and SMBus protocols
  • Hardware developers validating new peripherals

Buying Tip

Remember to add external pull-up resistors on SCL and SDA, and confirm your target logic voltage before connecting the VIO pin.

Elecvora expert review

Our verdict

The CP2112 Debug Board is a straightforward, well-integrated USB-to-I2C bridge that removes the need for custom drivers, making it a handy addition to any embedded workbench. Its GPIO flexibility and low-voltage support add useful versatility for a wide range of I2C tasks.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • No custom driver required thanks to HID class compliance
  • Eight configurable GPIO pins with alternate functions
  • Supports I/O voltages down to 1.8 V via VIO pin
  • Configurable clock speed and timeouts for bus tuning
  • Compact board with M3 mounting holes

Cons

  • External pull-up resistors must be added separately
  • Micro USB cable not included
  • No on-board level shifting; VIO must be supplied externally

Best for

Engineers and makers who need a quick, driver-free I2C/SMBus interface with GPIO control.

Not ideal for

Users looking for a stand-alone I2C programmer with integrated pull-ups or a USB cable.

Specifications

Model No. / NameCP2112
USB power supply4.0 to 5.25V
I/O pin voltage1.8V to VDD
Operating Temperature (°C)-40 ° C ~ 85 ° C
Shipping Weight0.01 kg
Shipping Dimensions5 × 5 × 1 cm

Frequently Asked Questions

Do I need to install a driver for this board?
No, the CP2112 uses the standard USB HID class, which is natively supported by most operating systems. You only need the Silicon Labs interface libraries for your host application.
What is the VIO pin used for?
The VIO pin sets the I/O voltage level for the SDA, SCL, and GPIO pins, allowing you to interface with devices down to 1.8 V. Connect it to the logic supply of your target system.
Can I use this board to program an EEPROM?
Yes, it can be used for I2C EEPROM read and write operations, provided you add appropriate pull-up resistors and configure the correct device address and timing.
Does the board include pull-up resistors for I2C?
No, external pull-up resistors are required on the SCL and SDA lines. You must add them according to your bus voltage and speed requirements.
What is the operating temperature range?
The board is rated for operation from -40 °C to 85 °C, making it suitable for most laboratory and industrial environments.
What is included in the package?
Package contents are not specified by the manufacturer. The board itself is the primary item; please refer to the product listing for any additional accessories.

Overview

The CP2112 Debug Board is a USB-to-I2C communication module that gives your computer a direct link to I2C and SMBus devices. At its core is the CP2112 bridge controller, which combines a USB 2.0 full-speed function controller, a transceiver, an oscillator, and eight GPIO pins on a single chip. Because it enumerates as a standard HID device, most operating systems recognise it immediately, so you can start communicating with your target hardware without writing firmware or installing a custom driver.

The board is small and easy to mount, measuring 29.5 mm by 21.3 mm with two M3 mounting holes and a Micro USB female port. It is aimed at engineers, makers, and technicians who need a reliable, low-friction way to read sensors, program EEPROMs, or toggle control lines over I2C.

Key Features

  • Driver-free HID operation: works with native OS support on Windows, Mac, and Linux.
  • Configurable SMBus interface: SDA and SCL signals with adjustable clock speed, timeouts, retry counter, and 7-bit device address.
  • Eight GPIO pins: each can be set as input or output and open-drain or push-pull; three pins offer alternate functions such as clock output (48 MHz to 94 kHz) and TX/RX LED toggling.
  • Flexible I/O voltage: a VIO pin allows interfacing down to 1.8 V, while the USB supply accepts 4.0 to 5.25 V.
  • On-chip resources: power-on reset circuit, 3.45 V voltage regulator, and a 194-byte one-time programmable ROM for custom product information.
  • 512-byte SMBus data buffer: helps manage larger transfers efficiently.

Specifications Explained

The USB power supply range of 4.0 to 5.25 V means the board can be powered from a standard USB port without additional regulation. The I/O pin voltage range of 1.8 V to VDD lets you match the logic level of your target device by supplying an appropriate reference voltage to the VIO pin. The operating temperature range of -40 °C to 85 °C covers typical laboratory and industrial environments. The 7-bit device address is the slave address the CP2112 will acknowledge; it will not respond to read/write requests sent to other addresses. External pull-up resistors are required on the SCL and SDA lines. The configurable clock speed and timeouts give you control over bus timing to suit different peripherals.

Compatibility and Requirements

The module uses the standard USB HID device class, so no custom driver is needed on most operating systems. Host applications communicate through interface libraries provided by Silicon Labs for Windows, Mac, and Linux, and open-access interface specifications allow development of custom APIs on any OS that supports HID. You will need a Micro USB cable (not included) and appropriate pull-up resistors for the I2C bus. The board does not include firmware for your target device; it is a bridge, not a programmer.

Typical Uses

  • Reading I2C sensors such as temperature, humidity, or accelerometers from a PC.
  • Debugging SMBus communication in embedded systems.
  • Programming or verifying I2C EEPROMs.
  • Controlling GPIO lines for test fixtures or simple automation.
  • Acting as a bridge for bring-up and validation of new I2C hardware.

What's in the Box

Package contents are not specified by the manufacturer. The board itself is the primary item; please check the product listing for any included accessories.

Quick specs

Model No. / Name
CP2112
USB power supply
4.0 to 5.25V
I/O pin voltage
1.8V to VDD
Operating Temperature (°C)
-40 ° C ~ 85 ° C
Shipping Weight
0.01 kg
Shipping Dimensions
5 × 5 × 1 cm
See all specifications