Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A four-pack of stainless steel compression springs measuring 6mm OD, 5mm ID and 45mm long, made for 3D printer heatbed leveling hardware. They supply consistent spring tension under the bed so adjustments hold while the plate stays cushioned.

Key Highlights

  • Four stainless steel compression springs per pack
  • 6mm outer diameter and 5mm inner diameter
  • 45mm free length with 0.5mm wire
  • Designed for 3D printer heatbed leveling and cushioning
  • Rust-resistant stainless steel construction
  • Lightweight spare-parts item for printer maintenance

Ideal For

  • 3D printer owners replacing worn bed-leveling springs
  • Makers building or modifying a heated bed mount
  • Kit builders who want spare leveling hardware on hand
  • Hobbyists maintaining several printers at once

Buying Tip

Measure your existing springs and leveling screw diameter before ordering, since the 6mm OD, 5mm ID and 45mm length must match your bed mount.

Elecvora expert review

Our verdict

A straightforward spare-parts set for printers that use this spring size. The stainless steel build and four-piece pack make it a sensible maintenance purchase, provided the dimensions match your bed hardware.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Stainless steel construction
  • Four springs in one pack
  • Clear, stated dimensions
  • Very light, so cheap to ship with other parts

Cons

  • Only one size is supplied
  • No installation hardware included
  • Compatibility depends entirely on matching your existing spring size

Best for

Owners of 3D printers with 6mm OD, 5mm ID, 45mm bed-leveling springs

Not ideal for

Printers that use a different spring diameter or length

Specifications

Item TypeSpring
MaterialStainless Steel
Outer Diameter (mm)6
Inner Diameter (mm)5
Length (mm)45
Size (mm)45x6
Shipping Weight0.005 kg
Shipping Dimensions5 × 2 × 1 cm

What's in the box

  • 4 x EasyMech 0.5mm stainless steel heatbed spacer compression springs, 6mm OD x 5mm ID x 45mm

Frequently Asked Questions

What are these springs used for?
They are compression springs intended for 3D printer heatbed leveling, sitting between the bed and frame to provide tension and cushioning while you adjust the leveling screws.
How many springs are included?
The pack contains four springs, each measuring 6mm outer diameter, 5mm inner diameter and 45mm in length.
Will these fit my 3D printer?
That depends on your bed hardware. Check that your existing springs are 6mm OD, 5mm ID and 45mm long, and that your leveling screws fit through the 5mm inner diameter.
Are they resistant to rust?
They are made from stainless steel, which is chosen for its resistance to rust in normal use around a heated bed.
Do I need any other parts to install them?
No additional parts are supplied with the springs. You reuse your existing leveling screws and bed hardware.
How should I care for them?
Keep them clean and dry, and inspect them periodically for deformation or corrosion, replacing any spring that has lost its shape.

Overview

The EasyMech heatbed spacer compression spring is a small but important piece of 3D printer hardware. It is designed to sit between the heated bed plate and the printer frame, working with the leveling screws to hold the bed at the height you set. This listing supplies four springs, so you can replace a full set at once rather than mixing old and new parts.

Each spring is made of stainless steel and measures 6mm on the outer diameter, 5mm on the inner diameter and 45mm in length. The 0.5mm wire gives the spring its compression behavior. Together, these dimensions make it a direct spare for bed-leveling setups that use this size of spring.

Key Features

  • Stainless steel material: suited to the warm, sometimes humid environment around a heated bed.
  • Four-piece pack: enough to refresh all four corners of a typical bed-leveling arrangement.
  • Defined dimensions: 6mm OD, 5mm ID and 45mm length make matching and replacement straightforward.
  • Compression design: provides spring tension while the leveling screws are adjusted.
  • Lightweight: shipping weight is just 0.005 kg, so the springs add almost nothing to a parts order.

Specifications Explained

Outer diameter (6mm): this is the overall width of the spring coil. It matters because the spring must fit inside the bed mount or washer area without rubbing.

Inner diameter (5mm): the clear space through the middle. The leveling screw passes through this opening, so the screw should be narrow enough to move freely inside it.

Length (45mm): the free length before compression. A longer spring gives more travel, while a shorter one feels firmer. Check the space available under your bed before fitting.

0.5mm wire: the thickness of the steel wire itself. It determines how stiff the spring feels when you tighten the leveling screws.

Compatibility and Requirements

These springs are intended for 3D printer heatbed leveling hardware that accepts a 6mm outer diameter, 5mm inner diameter and 45mm length spring. Confirm the dimensions of your existing springs and the diameter of your leveling screws before ordering. No other compatibility details are specified for this product.

Typical Uses

  • Replacing worn or compressed springs on a printer heatbed.
  • Assembling a custom bed mount or leveling setup.
  • Keeping a set of spare springs on hand for maintenance.
  • Using the springs as compression spacers in small mechanical projects where the dimensions suit.

What's in the Box

The pack contains four EasyMech 0.5mm stainless steel heatbed spacer compression springs, each 6mm OD x 5mm ID x 45mm long.

Quick specs

Item Type
Spring
Material
Stainless Steel
Outer Diameter (mm)
6
Inner Diameter (mm)
5
Length (mm)
45
Size (mm)
45x6
See all specifications