Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A six-piece set of brass M4 hex standoff spacers, 40mm tall with a 5.8mm male stud and female thread. They lift and lock PCBs securely in place while the hex body allows tightening with a wrench.

Key Highlights

  • Six brass hex standoff spacers in one set
  • M4 thread with male to female configuration
  • 40mm spacer height for generous board clearance
  • 5.8mm male stud and 15mm hole depth
  • Hexagonal body tightens easily with a wrench
  • Brass resists corrosion and oxidation

Ideal For

  • Drone and quadcopter builders mounting flight controllers or ESCs
  • PC builders and modders fitting boards inside a chassis
  • DIY electronics makers needing board clearance and airflow
  • Repair technicians replacing worn or missing standoffs
  • Hobbyists working with M4 threaded hardware

Buying Tip

Measure your existing screw or tapped hole and confirm it is M4 before ordering, and check that the 40mm hex width suits the wrench you plan to use.

Elecvora expert review

Our verdict

A practical, well-made brass standoff set for builders who need a tall M4 spacer with a secure hex grip. The six-piece pack covers most small mounting jobs, though buyers should verify the stated hex width before relying on a particular wrench.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Brass body resists corrosion and oxidation
  • Hex shape allows proper wrench tightening
  • Male to female design supports stacking
  • Six pieces per set for multi-point mounting

Cons

  • Only six pieces included, which may be short for larger builds
  • No screws or nuts supplied with the spacers
  • Hex across-flat size should be checked against your tools

Best for

Makers and technicians mounting PCBs with M4 hardware

Not ideal for

Builds that require a different thread size or very low-profile spacing

Specifications

Item TypeBrass Hex Standoff Spacer
Quantity6 Pcs.
Spacer Height (mm)40
Body ShapeHexagonal
Thread SizeM4
Stud Length (mm)5.8
GenderMale to female
MaterialBrass
Hole Depth (mm)15
Hex Size Across Flat (mm)40
Shipping Weight0.025 kg
Shipping Dimensions4 × 5 × 1 cm

What's in the box

  • 6 x M4 x 40mm male to female brass hex threaded pillar standoff spacers

Frequently Asked Questions

What thread size do these standoffs use?
They use an M4 thread on both the male stud and the female hole. Matching M4 screws or tapped holes are required.
How tall are the spacers?
The spacer height is 40mm, which sets the gap between the board and the mounting surface.
Can I tighten them by hand?
You can start them by hand, but the hexagonal body is designed to be gripped with a wrench for a secure fit.
Are screws included?
No. The set contains six standoff spacers only, so you will need your own M4 screws or mounting hardware.
Will brass corrode over time?
Brass offers good resistance to oxidation and corrosion, which helps the spacers hold up in normal use.
How deep is the female hole?
The hole depth is 15mm, so a screw or stud can enter up to that depth.

Overview

The EasyMech M4 x 40mm male to female brass hex threaded pillar standoff is a small but important piece of hardware for anyone mounting circuit boards. It raises a PCB away from a chassis, frame or neighbouring component and holds it at a fixed distance, so boards sit level and stay clear of anything that could short or obstruct them. This set contains six spacers, enough to support a board at multiple fixing points.

Each spacer is made from brass, a material chosen for its resistance to oxidation and corrosion as well as its mechanical strength. The hexagonal body gives you flat faces to grip with a wrench, so the spacer can be tightened properly rather than finger-tightened.

Key Features

  • Male to female format: the 5.8mm male stud threads into a matching female thread, allowing straightforward stacking or extension.
  • M4 thread size: a common metric thread that pairs with M4 nuts, screws and tapped holes.
  • 40mm spacer height: creates a substantial gap between board and mounting surface.
  • Hexagonal body: flat sides accept a wrench for secure tightening.
  • Brass construction: resists rust and oxidation and maintains good electrical conductivity.
  • Six pieces per set: enough for multi-point mounting on one board or several small projects.

Specifications Explained

The 40mm spacer height is the distance the standoff creates between the two surfaces it separates, which is useful when a board needs room for components underneath or improved airflow. The M4 thread describes the diameter and pitch of the threaded sections, so you can match it against your existing hardware. The 5.8mm stud length is the protruding male thread, while the 15mm hole depth tells you how far a screw or stud can enter the female end. The hex size across flat is given as 40mm in the product data; check this against your wrench before ordering.

Compatibility and Requirements

These standoffs are intended for M4 threaded applications. You will need matching M4 screws or tapped holes and, for tightening, a wrench that fits the hex body. No other mounting hardware is included beyond the six spacers.

Typical Uses

Common applications include mounting PCBs inside computer chassis, securing boards to quadcopter frames, spacing motor driver boards, and lifting circuit boards in DIY electronics projects where clearance and airflow matter.

What's in the Box

Six M4 x 40mm male to female brass hex threaded pillar standoff spacers.

Quick specs

Item Type
Brass Hex Standoff Spacer
Quantity
6 Pcs.
Spacer Height (mm)
40
Body Shape
Hexagonal
Thread Size
M4
Stud Length (mm)
5.8
See all specifications