Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A single 340 mm EFT arm assembly with a 40 mm outer and 37 mm inner diameter, made as a direct replacement for E410P and E416P drone frames. It restores frame stiffness and alignment after damage while adding only about 240 g.

Key Highlights

  • 340 mm arm assembly for EFT E410P and E416P frames
  • 40 mm outer diameter with 37 mm inner diameter tube
  • Lightweight at approximately 240 g per arm
  • Single-piece replacement for a bent or damaged arm
  • Engineered for structural strength without excess weight
  • Black finish that matches the frame assembly

Ideal For

  • Pilots repairing an EFT E410P frame after a crash
  • Builders maintaining an EFT E416P multirotor
  • Drone technicians keeping spare structural parts
  • Hobbyists rebuilding a damaged airframe

Buying Tip

Measure the length and tube diameters of your existing arm and confirm the E410P or E416P model before ordering, since this is a single arm for those frames only.

Elecvora expert review

Our verdict

A sensible replacement part for anyone maintaining an EFT E410P or E416P frame. It restores a single arm at a modest weight, though buyers must confirm the fit and supply their own mounting hardware.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Correct-fit part for E410P and E416P frames
  • Light at about 240 g
  • Clear 340 mm length and 40/37 mm diameters
  • Black finish suits the frame

Cons

  • Sold as one arm only
  • Mounting hardware not included
  • Not stated as compatible with other frames

Best for

Owners of EFT E410P or E416P frames doing a repair

Not ideal for

Builders of other drone frames or anyone needing a full arm set

Specifications

Item TypeAccessory
Model No. / NameArm Assembly
Length (mm)340
Outer Diameter (mm)40
Inner Diameter (mm)37
CompatibilityE410P/E416P
Weight (g)240
Shipping Weight0.25 kg
Shipping Dimensions35 × 5 × 5 cm

What's in the box

  • 1 x EFT Arm Assembly φ40/40*37*265 compatible with E410P/E416P

Frequently Asked Questions

Which frames does this arm fit?
It is listed as compatible with the EFT E410P and E416P. No other compatibility is stated, so check your frame model first.
How many arms are included?
One arm assembly is supplied per pack. If you need to replace several arms, order the matching quantity.
What are the arm dimensions?
The arm is 340 mm long with a 40 mm outer diameter and a 37 mm inner diameter tube.
How much does the arm weigh?
It weighs approximately 240 g, with a stated tolerance of about ±5% on dimensions and weight.
Does it include screws or mounting hardware?
The package contents list only the arm assembly, so mounting hardware is not included.
How should I care for the arm?
Inspect it after hard landings for bends or cracks and replace it if damaged, since arm condition affects frame stability.

Overview

The EFT Arm Assembly is a single structural arm intended for E410P and E416P drone frames. Arms carry the motors and take the load of every landing, so a bent or cracked arm affects how the airframe behaves in the air. This replacement lets you restore one arm instead of retiring the whole frame.

Each arm measures 340 mm in length with a 40 mm outer diameter and a 37 mm inner diameter. It weighs approximately 240 g, so it adds stiffness where it matters without turning the build into a heavyweight.

Key Features

  • Direct-fit arm assembly for EFT E410P and E416P frames
  • 340 mm length with a 40 mm OD and 37 mm ID tube
  • Approximately 240 g per arm for a light structural part
  • Black finish that blends with the frame
  • Sold as one arm assembly per pack

Specifications Explained

Length and diameter

The 340 mm length sets the motor position on the frame, so the replacement should match the arm you are removing. The 40 mm outer diameter and 37 mm inner diameter describe the tube wall and the fittings it accepts; check these figures against your existing arm before ordering.

Weight

At about 240 g, the arm is light enough for multirotor use while still providing the rigidity a frame needs. Keeping weight low on each arm helps the flight controller maintain balance across the airframe.

Compatibility and Requirements

This arm is listed as compatible with the EFT E410P and E416P only. It is not stated as fitting other frames. Installation requires the matching frame hardware, and the arm is supplied on its own, so reuse the fixings from the arm you are replacing or source them separately.

Typical Uses

Use it to replace a damaged arm after a hard landing, to rebuild an E410P or E416P frame, or to keep a spare on hand for field repairs. Because arm condition affects stability, replacing a suspect arm is a sensible part of routine frame maintenance.

What's in the Box

  • 1 x EFT Arm Assembly φ40/40*37*265 compatible with E410P/E416P

Note: dimensions and weight may vary by approximately ±5%.

Quick specs

Item Type
Accessory
Model No. / Name
Arm Assembly
Length (mm)
340
Outer Diameter (mm)
40
Inner Diameter (mm)
37
Compatibility
E410P/E416P
See all specifications