Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact 60A power distribution board with pre-soldered XT60 connectors for battery and power module. It centralises power routing in a multirotor build while keeping wiring tidy and weight minimal.

Key Highlights

  • 60A continuous rating with 120A support for bursts under 60 seconds
  • Pre-soldered XT60 connectors for battery and power module
  • 4mm mounting holes fit common frame plates
  • Compact and light at 0.017 kg shipping weight
  • Designed for PM02, PM02D and similar power modules
  • Clean central hub for battery power routing

Ideal For

  • Multirotor builders using a PM02 or PM02D power module
  • Drone makers who want tidy battery power routing
  • Pilots rebuilding a frame with a separate power module
  • Hobbyists assembling compact builds where weight matters

Buying Tip

Confirm your power module does not already include built-in distribution before ordering, since PM03, PM06 and PM07 modules do not need this board.

Elecvora expert review

Our verdict

A sensible, low-weight power distribution board for builds that use a separate power module. The pre-soldered XT60 connectors save time and remove two fiddly solder joints from the build.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Pre-soldered XT60 connectors for battery and power module
  • 60A continuous with 120A burst under 60 seconds
  • Very light at 0.017 kg shipping weight
  • 4mm mounting holes suit common frame hardware

Cons

  • Not needed if your power module already distributes power
  • Burst rating applies only under 60 seconds
  • Hole spacing is not specified, so check your frame first

Best for

Multirotor builds using a PM02, PM02D or similar separate power module

Not ideal for

Builds using PM03, PM06 or PM07 modules with built-in distribution

Specifications

Item TypePower Distribution Board
Connector TypePre-soldered XT60 for Power Module & Battery
Rated Current (A)60A
Current (A)120A (<60 sec)
Mounting Hole Diameter (mm)4mm
Shipping Weight0.017 kg
Shipping Dimensions17 × 9 × 2 cm

What's in the box

  • 1 x Holybro PDB Board

Frequently Asked Questions

Do I need this board if my power module already distributes power?
No. Power modules with built-in distribution, such as the PM03, PM06 and PM07, do not require this PDB.
Are the XT60 connectors already soldered?
Yes. The board ships with pre-soldered XT60 connectors for the power module and the battery.
What current can the board handle?
It is rated for 60A continuous, with 120A supported for bursts of less than 60 seconds.
What size are the mounting holes?
The mounting holes are 4mm in diameter. Check your frame plate spacing before mounting.
What is included in the package?
The package includes one Holybro PDB Board.
Will the board I receive match the photos exactly?
The actual product may vary in terms of version, so small differences are possible.

Overview

The Holybro PDB is a power distribution board built to give multirotor builds a single, tidy point where battery power is split and routed. Instead of running multiple leads back to the battery, you bring power in once and distribute it from the board. The battery and power module connections arrive pre-soldered with XT60 connectors, which removes two of the more awkward solder joints from your build.

This board is aimed at builders using a separate power module such as the PM02 or PM02D, or a similar unit that does not include built-in power distribution. If your power module already handles distribution, you do not need this board.

Key Features

  • Pre-soldered XT60 connectors for both the power module and the battery, reducing assembly work.
  • 60A continuous rating with support for 120A for periods under 60 seconds.
  • 4mm mounting holes for straightforward mounting to a frame plate.
  • Low weight at 0.017 kg shipping weight, so it barely affects your build.
  • Compact footprint with shipping dimensions of 17 x 9 x 2 cm.

Specifications Explained

Current rating

The 60A figure is the continuous current the board is rated to handle. The 120A figure applies only to short bursts of less than 60 seconds. In practice, this means the board suits builds whose steady current draw stays within 60A, with occasional peaks absorbed by the burst rating. Keep your expected continuous draw comfortably inside the continuous figure rather than relying on the burst number.

Connectors

The XT60 connectors for the power module and battery are already soldered in place. XT60 is a widely used connector format in multirotor builds, so this board slots into common power setups without adapters.

Mounting

The 4mm mounting hole diameter matches common frame hardware. Check your frame plate hole spacing before mounting, since hole spacing is not specified here.

Compatibility and Requirements

This PDB is intended for use with the PM02, PM02D or similar power modules. Power modules that already include built-in power distribution, such as the PM03, PM06 and PM07, do not require this board. Note that the actual product may vary in terms of version.

Typical Uses

This board fits multirotor builds where a separate power module is used and power needs to be distributed cleanly to the rest of the electronics. It is a natural fit for scratch builds and rebuilds where tidy wiring and low added weight matter.

What's in the Box

  • 1 x Holybro PDB Board

Quick specs

Item Type
Power Distribution Board
Connector Type
Pre-soldered XT60 for Power Module & Battery
Rated Current (A)
60A
Current (A)
120A (<60 sec)
Mounting Hole Diameter (mm)
4mm
Shipping Weight
0.017 kg
See all specifications