Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by Holybro, this flight controller accessories is a good fit for makers, students and electronics hobbyists. Main specs: item type Module; input voltage (v) HV: 2S-12S; max current (a) HV: 327A. Check that your power source supplies HV: 2S-12S before connecting it.

Key Highlights

  • Item Type: Module
  • Input Voltage (V): HV: 2S-12S
  • Max Current (A): HV: 327A

Ideal For

  • Room or desk lighting
  • Workbench lighting
  • Outdoor use

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeModule
Input Voltage (V)HV: 2S-12S
Max Current (A)HV: 327A
Output5.2V and 3A max
Weight (g)20
Shipping Weight0.04 kg
Shipping Dimensions16 × 9 × 3 cm

Overview

The Holybro PM02D Power Module High Voltage (2S -12S), made by Holybro, is listed in our flight controller accessories range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: Module
  • Input Voltage (V): HV: 2S-12S (match this to your power supply; too high a voltage can damage the part)
  • Max Current (A): HV: 327A (your supply must deliver at least this much current)
  • Output: 5.2V and 3A max
  • Weight (g): 20 (important for drones, RC models and anything you carry)
  • Shipping Weight: 0.04 kg (important for drones, RC models and anything you carry)
  • Shipping Dimensions: 16 × 9 × 3 cm (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

PM02D provides regulated power supply for your Pixhawk® 5X & 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 12S (HV). The Power Module comes completely assembled with XT60 connectors, wrapped in shrink tubing for physical damage protection. It is not designed to power servos, please use your aircraft's ESC/BEC for that. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact. Note: PM02D HV version is supported by PX4. For Ardupilot, it is supported in version 4.4 and later. Full setup guide can be found here. This PM uses I2C digital signal data output, Compatible with Pixhawk 5X/6X Series. NOT compatible with flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers. Current Rating: The PM02D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute).

Features:

  1. Regulated Output: 5.2V and 3A max for stable power supply
  2. Battery Compatibility: Supports LiPo batteries up to 12S (HV)
  3. Current Sensing: High-accuracy current sensing up to 327A for HV
  4. Monitoring Interface: I2C compatible interface for voltage and current monitoring
  5. Physical Protection: Wrapped in shrink tubing to prevent damage
  6. Connectors: Equipped with XT60 connectors for reliable connections

Package Includes:

1 x Holybro PM02D Power Module High Voltage (2S -12S)

Quick specs

Item Type
Module
Input Voltage (V)
HV: 2S-12S
Max Current (A)
HV: 327A
Output
5.2V and 3A max
Weight (g)
20
Shipping Weight
0.04 kg
See all specifications