Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by Holybro, this flight controller accessories is a good fit for makers, students and electronics hobbyists. Main specs: item type Module; input voltage (v) 6S battery; rated current (a) 60. Check that your power source supplies 6S battery before connecting it.

Key Highlights

  • Item Type: Module
  • Input Voltage (V): 6S battery
  • Rated Current (A): 60

Ideal For

  • Room or desk lighting
  • Workbench lighting
  • Outdoor use

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeModule
Input Voltage (V)6S battery
Rated Current (A)60
Max Current (A)120A (<60 sec)
Shipping Weight0.1 kg
Shipping Dimensions12 × 10 × 3 cm

Overview

The Holybro PM03D Power Module (Without XT30 Pre-soldered), made by Holybro, is listed in our flight controller accessories range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: Module
  • Input Voltage (V): 6S battery (note the battery type so you can order spares or the right charger)
  • Rated Current (A): 60 (your supply must deliver at least this much current)
  • Max Current (A): 120A (<60 sec) (your supply must deliver at least this much current)
  • Shipping Weight: 0.1 kg (important for drones, RC models and anything you carry)
  • Shipping Dimensions: 12 × 10 × 3 cm (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

PM03D provides regulated power supply as well as current consumption and battery voltage measurements via I2C digital protocol all through a 6pin 2.00mm CLIK-Mate cable. Compatible to flight controller that uses I2C power monitor such as the Pixhawk 5X and up. It is design for multi-rotor like the X500 V2. It has both XT-30 connectors preinstalled for motor ESCs and Battery, as well as two 5V BEC and a selectable 8V/12V output different kinds of peripheral devices. Note Full setup guide can be found here. This PM uses I2C digital signal data output, Compatible with Pixhawk 5X/6X Series. NOT compatible with flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers. Power Module Comparison Table

Useful link:

For setting the module refer to the link.

Features:

  1. Plug & play, no additional setup required for QGroundcontrol & Mission Planner
  2. XT-30 connectors and solder pads for easy motor ESC connection
  3. Onboard voltage regulators: two 5.2V & one selectable 8V/12V
  4. 5V/A ports for powering companion computer or peripheral device
  5. Selectable 8V or 12V triple row pin header for powering peripheral device

Package Includes:

1x PM06 board

1x 80mm XT30 connector wire (pre-soldered)

1x Electrolytic capacitor: 220uF 63V (pre-soldered)

1x 2.0mm pitch CLIK-Mate 6pin cable (To power flight controller)

1 x 4pin JST GH to USB Type C

1 x 4pin JST GH to barrel plug (2.1*5.5mm)

1 x 4pin JST GH to barrel plug (2.5*5.5mm)

1 x 3pin Pin Dupont Cable (2pc)

1x Nylon standoffs & nuts

Quick specs

Item Type
Module
Input Voltage (V)
6S battery
Rated Current (A)
60
Max Current (A)
120A (&lt;60 sec)
Shipping Weight
0.1 kg
Shipping Dimensions
12 × 10 × 3 cm
See all specifications