Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 2S-14S power module that feeds your flight controller 5.2V/3A and reports battery voltage and current via analog signal. It includes a pre-soldered XT60, 12AWG wires, capacitor, and 6-pin JST-GH cable for straightforward installation.

Key Highlights

  • Wide 2S-14S input range for diverse battery setups
  • 70A continuous and 120A burst PCB current ratings
  • 5.2V/3A output (18W max) powers flight controller
  • Integrated power distribution for four ESCs
  • Pre-soldered XT60, 12AWG wires, and capacitor
  • Compact 35x35x5mm, 24g design with 30.5x30.5mm mounting

Ideal For

  • FPV freestyle pilots building 5-inch quads
  • Multirotor builders using 2S-14S batteries
  • Drone enthusiasts needing analog voltage and current sensing
  • DIY drone makers with four-ESC power distribution
  • Pilots upgrading to a compact power module

Buying Tip

Check your flight controller's power module compatibility and confirm your build's current draw stays within the pre-soldered XT60 and 12AWG wire ratings (30A continuous, 60A burst) or plan to upgrade them.

Elecvora expert review

Our verdict

The Holybro PM06 V2 is a well-rounded analog power module that combines a wide input range, solid current ratings, and integrated ESC distribution in a lightweight package. Its pre-soldered connections simplify installation, though users must respect the XT60 and wire limits and avoid Pixhawk 5X/6X compatibility.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Broad 2S-14S input range
  • High 70A continuous PCB rating
  • Integrated power distribution for four ESCs
  • Pre-soldered XT60, wires, and capacitor
  • Compact and lightweight at 24g

Cons

  • Not compatible with Pixhawk 5X and 6X
  • Pre-soldered XT60 and 12AWG wire limited to 30A continuous / 60A burst

Best for

Multirotor builders needing a compact analog power module with ESC distribution

Not ideal for

Pixhawk 5X or 6X users requiring a digital power module

Specifications

Item TypeModule
Input voltage (14S version)2S-14S
PCB Cont. Current Rating70A
PCB Burst Current Rating120A (<60 Sec)
OutputDC 5.2V & 3A Max
Ouput Max Power18W
Voltage Divider18.182
Amperes per Volt36.364
Dimensions (L x W x H) mm35x35x5mm
Mounting Hole Diameter (mm)30.5mm*30.5mm
Weight (g)24
Shipping Weight0.031 kg
Shipping Dimensions15 × 8 × 2 cm

What's in the box

  • 1x PM06 Power Module
  • 1x JST GHR 6-pin 1.25mm pitch cable

Frequently Asked Questions

What is the input voltage range of the PM06 V2?
The module supports a 2S to 14S battery input range.
Is the PM06 V2 compatible with Pixhawk 5X or 6X?
No, it uses analog output and is not compatible with Pixhawk 5X or 6X, which require a digital power module like the PM02D.
What current can the pre-soldered XT60 and wire handle?
The pre-soldered XT60 plug and 12AWG wire are rated for 30A continuous and 60A burst (<60 seconds). For higher current, change the plug and wire.
What is included with the PM06 V2?
The package includes 1x PM06 Power Module and 1x JST GHR 6-pin 1.25mm pitch cable.
How do I connect the PM06 V2 to my flight controller?
Use the included 6-pin JST-GH cable to connect the module to your flight controller's power module port.
What are the voltage divider and amperes per volt values?
The voltage divider is 18.182 and amperes per volt is 36.364, used for configuring the analog readings in your flight controller.

Overview

The Holybro PM06 V2 Power Module is a compact power distribution and sensing board designed for multirotor flight controllers. It takes power from your main battery and provides a regulated 5.2V supply to the flight controller while sending analog voltage and current signals over a 6-pin JST-GH cable. With an input range of 2S to 14S, it suits a broad spectrum of battery configurations. The board also distributes power to four ESCs, reducing wiring complexity in builds.

Key Features

  • Wide voltage compatibility: Operates from 2S to 14S batteries.
  • High current PCB: 70A continuous and 120A burst (<60 seconds) ratings.
  • Clean 5.2V output: Up to 3A (18W max) for flight controller power.
  • Analog monitoring: Voltage divider 18.182 and amperes per volt 36.364 for setup.
  • Integrated ESC distribution: Power for four ESCs on one board.
  • Ready to install: Pre-soldered XT60, 12AWG wires, capacitor, and JST-GH cable.

Specifications Explained

The 2S-14S input range means the module can handle battery packs from 7.4V nominal to 51.8V nominal, covering small to large multirotors. The PCB continuous current rating of 70A indicates the board's power path can sustain 70A, while the 120A burst rating (<60 seconds) provides headroom for short peaks. The 5.2V/3A output (18W max) is dedicated to powering the flight controller and its peripherals. For telemetry setup, the voltage divider value of 18.182 and amperes per volt of 36.364 are used to calibrate the analog readings in your flight controller software. The 30.5x30.5mm mounting hole spacing matches common flight controller stacks.

Compatibility and Requirements

The PM06 V2 uses analog data output and is not compatible with Pixhawk 5X or 6X flight controllers, which require a digital power module such as the PM02D. The pre-soldered XT60 plug and 12AWG wire are rated for 30A continuous and 60A burst (<60 seconds). If your build draws higher current, you must change the plug type and wire size accordingly. Ensure your flight controller supports analog power module input via a 6-pin JST-GH connector.

Typical Uses

This module is ideal for multirotor builds where a compact, analog power module is needed to supply the flight controller and distribute power to four ESCs. It suits FPV racing and freestyle quads, aerial photography rigs, and other DIY drones using 2S to 14S batteries. The pre-soldered connectors and included capacitor help speed up assembly.

What's in the Box

  • 1x PM06 Power Module
  • 1x JST GHR 6-pin 1.25mm pitch cable

Quick specs

Item Type
Module
Input voltage (14S version)
2S-14S
PCB Cont. Current Rating
70A
PCB Burst Current Rating
120A (&lt;60 Sec)
Output
DC 5.2V &amp; 3A Max
Ouput Max Power
18W
See all specifications