
1 / 6 · Click to enlarge
AI Summary
A 36x50mm power distribution board with a built-in XT60 socket and regulated 5V and 12V BEC outputs. It simplifies wiring for 3S-4S multirotors by feeding six ESCs and low-voltage electronics from one compact board.
Key Highlights
- Built-in XT60 socket for direct LiPo connection
- Regulated 5V output up to 2A for receivers and flight controllers
- 12V BEC output for cameras, VTXs and LEDs
- Six pairs of ESC solder tabs for H or X frames
- 4-layer PCB with 2oz copper tracks
- Compact 36 x 50mm board weighs only 11g
Ideal For
- FPV racing pilots building 3S or 4S quads
- DIY drone builders needing regulated 5V and 12V rails
- Makers wiring cameras, VTXs and LEDs on multirotors
- Hobbyists assembling H or X frame configurations
Buying Tip
Confirm your build's total current draw and cell count against the board's continuous and peak ratings, and remember the 12V output is only regulated on 4S packs.
Elecvora expert review
Our verdict
The Mateksys PDB-XT60 packs a useful set of power distribution features into a small, lightweight board. Its built-in XT60 socket and regulated 5V and 12V outputs make it a practical choice for 3S-4S multirotor builds where clean wiring matters.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Integrated XT60 socket saves wiring and space
- Regulated 5V and 12V outputs cover common accessories
- Six ESC tab pairs support H and X layouts
- Compact and light at 36 x 50mm and 11g
Cons
- Requires soldering for ESC and accessory connections
- 12V output is not regulated on 3S packs
- Current ratings limit use to moderate-power builds
Best for
FPV and DIY multirotor builders using 3S or 4S packs who need a compact power hub with dual BEC outputs.
Not ideal for
High-current builds exceeding the board's 25A/15A continuous ratings or users who prefer plug-and-play wiring.
Specifications
| Item Type | Power Distribution Board |
|---|---|
| Material | 2oz Copper (Track ) |
| Output Current (A) | 25A @4 and 15A @6 |
| Peak Current (A) | 30A @4 and 20A@6 (for 10 seconds) |
| Length (mm) | 36 |
| Width (mm) | 50 |
| Weight (g) | 11 |
| Shipping Weight | 0.016 kg |
| Shipping Dimensions | 6 × 8 × 2 cm |
What's in the box
- 1 x PDB-XT60 with BEC 5V and 12V board
- 1 x XT60 male connector
Frequently Asked Questions
What battery types can I use with this board?
How many ESCs can I connect?
What is the maximum current for the 5V and 12V outputs?
Does the 12V output work with a 3S battery?
What is included in the package?
Do I need to solder to use this board?
Overview
The Mateksys PDB-XT60 is a power distribution board for multirotor aircraft that combines battery connection, ESC power distribution and regulated voltage outputs on a single compact PCB. It is intended for 3S and 4S LiPo setups and provides a clean way to route power to six ESCs while supplying lower-voltage electronics from built-in BECs. The board measures 36mm by 50mm and weighs 11g, so it fits neatly into weight-conscious FPV and racing builds.
Key Features
- Integrated XT60 socket: connect your LiPo pack directly without an extra adapter cable.
- Dual BEC outputs: regulated 5V and 12V rails power receivers, flight controllers, cameras, video transmitters and LEDs.
- Six ESC connection points: total six pairs of solder tabs suit both H and X frame layouts.
- Status LEDs: indicators show when the 5V and 12V outputs are active.
- Robust PCB construction: 4-layer board with 2oz copper tracks and 1.6mm thickness.
Specifications Explained
The board is rated for 25A continuous at 4S and 15A continuous at 6S, with peak currents of 30A at 4S and 20A at 6S for up to 10 seconds. These figures describe the main power distribution path, so choose ESCs and motors that stay within these limits for your cell count. The 5V BEC delivers 2A continuously (2.5A for 10 seconds per minute) with approximately 40mV ripple at a 2A load, which is suitable for typical receivers, flight controllers and small servos. The 12V BEC provides 500mA continuously (0.8A for 5 seconds per minute) when running from a 4S pack; on 3S the 12V output tracks approximately 1V below the pack voltage rather than regulating to 12V. Both outputs are short-circuit tolerant for 5 seconds per minute.
Compatibility and Requirements
The PDB-XT60 is designed for 3S to 4S LiPo batteries connected via the onboard XT60 socket. It supports up to six ESCs through solder tabs. The 12V output is regulated when using a 4S pack (13-18V DC input); with a 3S pack the 12V rail behaves as a pass-through at roughly pack voltage minus 1V. Soldering is required to attach ESCs and any accessory wiring. Check that your total current draw stays within the board's continuous and peak ratings.
Typical Uses
This board is well suited to FPV racing quads, freestyle multirotors and general DIY drone projects where a compact power hub with regulated 5V and 12V rails is useful. It can simplify wiring for builds using cameras, video transmitters and LED strips that need a stable 12V supply, while the 5V rail feeds the flight controller and receiver.
What's in the Box
- 1 x PDB-XT60 with BEC 5V and 12V board
- 1 x XT60 male connector
Quick specs
- Item Type
- Power Distribution Board
- Material
- 2oz Copper (Track )
- Output Current (A)
- 25A @4 and 15A @6
- Peak Current (A)
- 30A @4 and 20A@6 (for 10 seconds)
- Length (mm)
- 36
- Width (mm)
- 50
















