Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact MOSFET breakout board that lets 3-20V logic signals switch 5-35V DC loads up to 5A, with PWM support for speed or brightness control. Input and output are isolated for safe, interference-free operation.

Key Highlights

  • 3-20V input accepts logic-level and weak signals
  • 5-35V output switches loads up to 5A
  • PWM input for motor speed and LED brightness
  • Input and output circuits fully isolated
  • Compact 46 x 25 mm board weighs only 12g
  • Works with microcontroller IO ports and PLC interfaces

Ideal For

  • Electronics hobbyists building Arduino or Raspberry Pi projects
  • Makers needing to switch DC motors, pumps or solenoids
  • Automation engineers interfacing PLCs with DC loads
  • LED lighting projects requiring PWM dimming
  • Students learning about MOSFET switching circuits

Buying Tip

Confirm that your load's voltage is between 5 and 35 V DC and its current draw stays below 5 A, and remember to provide a separate power supply for the load.

Elecvora expert review

Our verdict

This MOSFET board offers a straightforward way to switch moderate DC loads from logic-level signals, with the added benefit of PWM control and input-output isolation. It is a practical building block for hobbyist and light industrial projects where a compact, low-cost solution is needed.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Wide input voltage range suits many logic families
  • Isolated input and output improve safety and reduce interference
  • PWM support enables speed and brightness control
  • Very compact and lightweight
  • Simple wiring with no programming required

Cons

  • Maximum 5 A output may be limiting for larger loads
  • Requires a separate power supply for the load
  • Package contents are not clearly specified

Best for

Makers and engineers switching DC motors, LEDs, pumps or valves up to 5 A from logic signals

Not ideal for

High-power loads exceeding 5 A or applications requiring mains AC switching

Specifications

Operating Voltage (V)3 to 20
Input current (mA)5mA
Output Voltage5 ~ 35
Max. Operating Current (A)5
Length (mm)46
Width (mm)25
Weight (g)12
Shipping Weight0.015 kg
Shipping Dimensions5 × 3 × 2 cm

Frequently Asked Questions

What is the maximum voltage I can use for the control signal?
The input accepts signals from 3 V to 20 V. Do not exceed 20 V on the input terminals.
Can I use this board with a 3.3 V microcontroller?
Yes, the minimum input voltage is 3 V, so 3.3 V logic is compatible.
What is the maximum current for the load?
The board can handle up to 5 A on the output. Ensure your load's current draw, including startup surges, stays below this limit.
Does the board support PWM for dimming or speed control?
Yes, you can apply a PWM signal to the input to control motor speed or LED brightness.
Is a separate power supply needed for the load?
Yes, the output side requires its own DC power supply within 5 to 35 V. The input signal only triggers the switch.
What is included in the package?
Package contents are not specified in the product data. Please check with the seller for details.

Overview

The Generic F5305S MOSFET Electronic Switch DC Controlling Board is a small breakout module built around an F5305S power MOSFET. It is designed to bridge the gap between low-power control electronics and higher-power DC devices. A digital high or low signal from a microcontroller, PLC or other logic source can trigger the board, which then switches a separate DC load on the output side. Because the input and output are isolated, the control signal is protected from the load circuit, and switching noise is less likely to affect sensitive electronics.

With an operating voltage range of 3 to 20 V on the input and an output range of 5 to 35 V at up to 5 A, the board covers many common hobby and light industrial tasks. It also accepts PWM signals, so you can vary motor speed or LED brightness rather than simply turning a load on or off.

Key Features

  • F5305S power MOSFET: the core switching component handles moderate DC currents efficiently.
  • Wide input range: accepts 3 to 20 V trigger signals, including digital high/low levels.
  • Flexible output: switches 5 to 35 V DC loads up to a maximum of 5 A.
  • PWM capable: use a PWM signal to control motor speed or lamp brightness.
  • Isolated input and output: keeps the control side separate from the load side.
  • Compact footprint: 46 mm long, 25 mm wide and only 12 g, easy to fit into tight builds.

Specifications Explained

Operating voltage (3-20 V): this is the voltage range for the control signal at the input terminal. It means the board can be driven by 3.3 V and 5 V microcontrollers as well as higher-voltage logic such as 12 V or 24 V PLC outputs, provided the signal stays within the range.

Input current (5 mA): the trigger input draws very little current, so it will not load down the controlling device. This makes it safe to connect directly to most microcontroller IO pins.

Output voltage (5-35 V): the load you switch can be powered from a supply anywhere between 5 V and 35 V DC. The output voltage is independent of the input signal voltage, giving you flexibility in choosing a motor, lamp or solenoid.

Max operating current (5 A): the board can handle loads drawing up to 5 A continuously. Always check that your load's current draw stays below this limit, and consider a margin for startup surges.

Dimensions and weight: at 46 x 25 mm and 12 g, the board is small enough for embedded projects and light enough not to strain wiring.

Compatibility and Requirements

The board is compatible with any control source that can provide a digital high or low signal within 3 to 20 V, such as microcontroller IO ports, PLC interfaces and DC power supplies. It requires a separate DC power source for the load within the 5 to 35 V range. No programming is needed; the board responds directly to the trigger signal. For PWM control, the signal source must be able to generate a PWM waveform.

Typical Uses

  • Controlling DC motors and micro pumps in automation projects
  • Dimming or switching LED strips and bulbs
  • Driving solenoid valves from logic-level signals
  • Interfacing PLC outputs with higher-current DC devices
  • Adding PWM speed control to small motorised mechanisms

What's in the Box

Package contents are not specified for this listing. Please check the product packaging or contact the seller for details.

Quick specs

Operating Voltage (V)
3 to 20
Input current (mA)
5mA
Output Voltage
5 ~ 35
Max. Operating Current (A)
5
Length (mm)
46
Width (mm)
25
See all specifications