Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A U-BLOX NEO-7M GPS module with an onboard HMC5883L compass, pre-configured for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8. It delivers 5Hz position updates and heading data through a cased, plug-and-play receiver with backup battery and EEPROM.

Key Highlights

  • U-BLOX NEO-7M receiver with 56 channels and -161 dBm tracking sensitivity
  • Onboard HMC5883L digital compass supplies heading alongside GPS position
  • Pre-configured at 38400 baud with 5Hz GGA, GSA and RMC output
  • Active ceramic patch antenna in a moulded plastic protective case
  • Rechargeable backup battery enables hot starts; EEPROM keeps settings
  • 6-pin and 4-pin connectors for GPS and I2C compass wiring

Ideal For

  • Multirotor builders running APM 2.6/2.8 autopilots
  • Pixhawk 2.4.6/2.4.8 users adding GPS and compass
  • Fixed-wing pilots setting up return-to-home and waypoints
  • FPV pilots who want position hold in open areas
  • Makers building autonomous navigation test platforms

Buying Tip

Check whether your APM board is a 2.0 or 2.5 with an internal compass, because that trace must be cut before connecting this external compass module.

Elecvora expert review

Our verdict

A practical, pre-configured GPS and compass unit that removes most of the setup friction from APM and Pixhawk builds. The cased housing, backup battery and retained settings make it a sensible choice for repeatable installations.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Pre-flashed at 38400 baud with 5Hz output for plug-and-play use
  • Onboard compass reduces separate component count
  • Backup battery and EEPROM support hot starts and saved settings
  • Cased design with standard 45mm x 45mm mounting holes

Cons

  • Requires disabling the internal compass on APM 2.0 and 2.5 boards
  • Only the module is included, so wiring must suit your own frame layout
  • Accuracy figures are typical values rather than guaranteed per-unit results

Best for

APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8 builds needing GPS position and heading

Not ideal for

Autopilots outside the listed APM and Pixhawk versions

Specifications

Item TypeGPS Module
Model No. / NameUblox NEO 7M
Receiver frequencyL1 [1575.42MHz]
Input Voltage (V)3.5 to 5.5
Main ChipU-BLOX NEO-7M
Position Accuracy (Meter)2.5, 2
Acceleration (g)<4
Navigation Update Rate5Hz
Operating Temperature (°C)-24 to 84
Tracking Sensitivity (dBm)-161 dBm
Avg Cold Start Time (s)38
Warm Start Time (s)35
Additional Specs.Boot Time: 1S, Capture Time: 0.1s Average, Co-Ordinate System: WGS-84
Maximum Altitude (m)18000
Maximum Speed515 m/s
Overall Dimension60 x 11.5 (DxH)
Weight (g)26
Cable Length20
Shipping Weight0.08 kg
Shipping Dimensions8 × 8 × 5 cm

What's in the box

  • 1 x NEO 7M GPS module

Frequently Asked Questions

Which flight controllers does this GPS module work with?
It is configured for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8 systems. The default 38400 baud rate matches that pre-flashed configuration.
Does it include a compass?
Yes. An HMC5883L digital compass is built into the module and connects through the 4-pin I2C lead.
What input voltage does it need?
The module accepts 3.5 to 5.5V, which covers common flight controller power rails.
Why do I need to cut a trace on some APM boards?
APM 2.0 and APM 2.5 boards have an internal compass that must be disabled before an external compass module is connected. APM 2.6 does not have this internal compass.
What is included with the module?
The package contains one NEO 7M GPS module with its 6-pin GPS connector and 4-pin I2C compass connector.
How should I care for the module?
Keep it mounted clear of obstructions with a sky view, avoid stressing the antenna and cables, and stay within the -24 to 84 degrees Celsius operating range.

Overview

The NEO 7M GPS with Compass is a positioning and heading module intended for multirotor and fixed-wing builds that use APM 2.6/2.8 or Pixhawk 2.4.6/2.4.8 autopilots. At its centre is the U-BLOX NEO-7M receiver, a 56-channel L1 module tuned to 1575.42MHz. An HMC5883L digital compass sits on the same board, giving the flight controller a heading reference in addition to satellite position.

The module arrives pre-configured and flashed at 38400 baud with a 5Hz navigation update rate, outputting GGA, GSA and RMC frames. It is housed in a moulded plastic case with a super bright LED backplane and standard 45mm x 45mm mounting holes, which keeps the electronics protected and makes frame installation straightforward.

Key Features

  • U-BLOX NEO-7M main chip with 5Hz navigation update rate
  • Active circuitry ceramic patch antenna for reliable signal capture
  • Onboard HMC5883L compass for heading data over I2C
  • Rechargeable backup battery for hot starts and an I2C EEPROM for permanent configuration retention
  • 6-pin connector for the GPS link and a 4-pin connector for compass-only use; both 4-pin ports can be used at once
  • Moulded plastic enclosure with 45mm x 45mm mounting pattern

Specifications Explained

Position accuracy of 2.5m and 2m describes the horizontal precision you can expect, which is adequate for position hold and waypoint work. Tracking sensitivity of -161 dBm helps the receiver hold satellites in weaker signal conditions, while a 38-second cold start and 35-second warm start reflect typical acquisition times; the backup battery supports faster hot starts once the module has run recently.

The 3.5 to 5.5V input range covers common flight controller power rails. Maximum altitude of 18000m and maximum speed of 515 m/s are far beyond typical hobby flight envelopes. The module measures 60mm in diameter and 11.5mm in height, weighs 26g and includes a 20cm cable. Operating temperature is rated from -24 to 84 degrees Celsius, and the coordinate system is WGS-84.

Compatibility and Requirements

The module is configured for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8 systems. Note that APM 2.0 and APM 2.5 boards carry an internal compass, which must be disabled by cutting a trace before an external compass module is connected; APM 2.6 does not have this internal compass. Wiring uses the supplied 6-pin GPS connector and 4-pin I2C compass connector, and the default 38400 baud rate matches the pre-flashed configuration.

Typical Uses

Use this module when you need the autopilot to know where it is and which way it faces. That makes it suitable for position hold, autonomous flight, return-to-home and waypoint navigation on multirotors and fixed-wing aircraft. The cased design suits airframes where the module is exposed to the elements.

What's in the Box

One NEO 7M GPS module is included. The module is supplied with its 6-pin GPS connector and 4-pin I2C compass connector as part of the assembly.

Quick specs

Item Type
GPS Module
Model No. / Name
Ublox NEO 7M
Receiver frequency
L1 [1575.42MHz]
Input Voltage (V)
3.5 to 5.5
Main Chip
U-BLOX NEO-7M
Position Accuracy (Meter)
2.5, 2
See all specifications