Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A pre-cut A4 FEP film (290 x 210mm) for 5.5 and 8.9 inch resin 3D printers. Its non-stick, transparent surface helps each layer release cleanly and keeps UV light transmission consistent.

Key Highlights

  • A4 size 290 x 210mm sheet fits 5.5 and 8.9 inch resin printers
  • Non-stick FEP surface supports clean layer release
  • High transparency for consistent UV light transmission
  • Resists tearing, scratching and wear across print cycles
  • Heat resistant for long or warm printing sessions
  • Lightweight at about 80g for easy storage and fitting

Ideal For

  • Owners of 5.5 inch resin 3D printers needing a spare vat film
  • Operators of 8.9 inch resin printers doing routine vat maintenance
  • Hobbyists who want a pre-cut A4 sheet instead of trimming film
  • Workshops keeping consumables ready for quick film replacement

Buying Tip

Measure your resin vat's film area and confirm it fits within 290 x 210mm before ordering, and keep the sheet flat and uncreased until installation.

Elecvora expert review

Our verdict

A sensible consumable for anyone running 5.5 inch or 8.9 inch resin printers: the pre-cut A4 size removes trimming work and the FEP material delivers the transparency and release behaviour the process depends on. It is a maintenance part, not an upgrade, so buy it to replace worn film rather than to change print quality.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Pre-cut 290 x 210mm A4 size simplifies fitting
  • Clear FEP supports consistent UV light transmission
  • Non-stick behaviour aids layer release
  • Resists wear for repeated print cycles

Cons

  • Only listed for 5.5 inch and 8.9 inch printers
  • Film is a wear item and will need periodic replacement
  • No installation tools included

Best for

Routine vat film replacement on 5.5 and 8.9 inch resin printers

Not ideal for

Printers whose vats fall outside the 290 x 210mm sheet size

Specifications

Item Type3D Printer's Film
Compatibility5.5, 8.9 Resin 3D Printers
MaterialFEP
Length (mm)290
Width (mm)210
Weight (g)80
ColorTransparent
Shipping Weight0.096 kg
Shipping Dimensions33 × 24 × 3 cm

What's in the box

  • 1 x Phrozen FEP Film, A4 size, 290 x 210mm

Frequently Asked Questions

What is FEP film used for in resin printing?
It forms the transparent, non-stick base of the resin vat, letting UV light through to cure layers while helping each layer release from the vat floor.
Which printers is this sheet compatible with?
It is listed for 5.5 inch and 8.9 inch resin 3D printers. Confirm your vat dimensions fit within 290 x 210mm before ordering.
Does it require power or electronics?
No. It is a passive film sheet with no electrical components; it simply fits into the resin vat.
What is included in the package?
The package contains one Phrozen FEP film in A4 size, 290 x 210mm.
How do I care for the film?
Keep it flat and free of creases before fitting, clean the vat gently, and avoid sharp tools that could scratch the surface.
When should I replace the film?
Replace it when the film becomes cloudy, scratched or dented, or when prints begin failing to release reliably.

Overview

The Phrozen FEP Film is a replacement release film for resin 3D printers. This sheet is supplied in A4 size at 290 x 210mm and is intended for 5.5 inch and 8.9 inch resin machines. FEP is the transparent membrane that sits at the bottom of the resin vat, separating the liquid resin from the printer's light source while allowing UV light through to cure each layer.

Because the film is a wear item, it gradually picks up cloudiness, scratches or dents during normal use. Keeping a spare A4 sheet ready lets you refresh the vat and return to printing without cutting material by hand.

Key Features

  • Non-stick surface: the smooth FEP layer helps cured layers release from the vat floor, reducing the chance of print defects.
  • Durable material: made from FEP to resist tearing, scratching and wear through frequent printing.
  • High transparency: clear film supports precise UV light transmission for detailed output.
  • Heat resistance: performs consistently during prolonged or higher-temperature printing sessions.
  • Pre-cut A4 format: the 290 x 210mm size simplifies installation and replacement.

Specifications Explained

Material: FEP (fluorinated ethylene propylene) is chosen for its release properties and optical clarity, both of which matter for layer-by-layer resin printing.

Dimensions: at 290mm long and 210mm wide, the sheet is sized as A4, giving enough material for vats on 5.5 inch and 8.9 inch printers.

Weight: the film weighs about 80g, so it is thin and easy to handle during fitting.

Colour: transparent, so light passes through to the resin with minimal interference.

Compatibility and Requirements

This film is listed for 5.5 inch and 8.9 inch resin 3D printers. Check the vat dimensions of your machine against the 290 x 210mm sheet before ordering. Installation requires removing the old film and securing the new one in the vat frame according to your printer's vat design.

Typical Uses

Use this sheet when the existing vat film becomes cloudy, scratched or dented, or keep it as a spare for routine maintenance. It suits hobbyists and workshops running 5.5 inch and 8.9 inch resin printers who want a ready-sized replacement on hand.

What's in the Box

  • 1 x Phrozen FEP Film, A4 size, 290 x 210mm

Quick specs

Item Type
3D Printer's Film
Compatibility
5.5, 8.9 Resin 3D Printers
Material
FEP
Length (mm)
290
Width (mm)
210
Weight (g)
80
See all specifications