Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A USB-connected PICkit3 debugger and programmer board for PIC and dsPIC Flash microcontrollers, with a 1.8V to 5V target range and support for up to 512K byte flash. It lets you program, verify and debug in real time using the MPLAB IDE.

Key Highlights

  • Full-speed USB connection using standard Windows drivers
  • Target voltage range from 1.8V to 5V for low-power designs
  • Programs up to 512K byte of flash memory
  • Real-time execution with peripheral freeze at breakpoints
  • Diagnostic LEDs for power, active and status
  • Built-in over-voltage and short-circuit monitoring

Ideal For

  • Embedded engineers developing PIC and dsPIC Flash designs
  • Students learning microcontroller programming and debugging
  • Makers building PIC-based control and sensor projects
  • Technicians verifying firmware and configuration memory
  • Hobbyists moving from simulation to real hardware

Buying Tip

Confirm your target microcontroller is a PIC or dsPIC Flash device and that your board runs within 1.8V to 5V before ordering.

Elecvora expert review

Our verdict

A sensible low-cost entry into PIC and dsPIC development, covering the programming and debugging basics without extra hardware. It suits bench work where a stable USB link and a wide target voltage range matter more than a large enclosure.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Wide 1.8V to 5V target voltage range
  • Real-time execution and peripheral freeze at breakpoints
  • Erase and verify across all memory types
  • Diagnostic LEDs and built-in over-voltage and short-circuit monitor

Cons

  • Requires a PC running the MPLAB IDE to be useful
  • Only a 6-pin target cable is included, so check your board's connector
  • No enclosure, so it is best kept on a bench rather than in the field

Best for

Bench development and learning with PIC and dsPIC Flash microcontrollers

Not ideal for

Projects needing a standalone programmer with no PC attached

Specifications

Voltage Rating (V)1.8 to 5
Supply Voltage1.8 ~ 5
Flash Memory (Kbytes)512
Length (mm)95
Width (mm)40
Weight (g)30
Shipping Weight0.05 kg
Shipping Dimensions14 × 8 × 4 cm

What's in the box

  • 1 x PICkit3 Programmer
  • 1 x USB cable
  • 1 x 6-pin cable

Frequently Asked Questions

What is this board used for?
It programs and debugs PIC and dsPIC Flash microcontrollers. It reads and writes program and data memory, erases all memory types with verification, and supports real-time debugging.
Which software do I need?
The board is designed for the MPLAB Integrated Development Environment, which provides the graphical interface for programming and debugging over USB.
What target voltage does it support?
The target range is 1.8V to 5V, so it works with both low-voltage and 5V PIC designs.
How much flash can it program?
It supports programming up to 512K byte of flash memory.
What cables come with it?
The package includes the programmer, a USB cable and a 6-pin cable for the target connection.
How do I know it is working?
Three diagnostic LEDs indicate power, active and status, and a built-in over-voltage and short-circuit monitor helps protect the setup.

Overview

The PICkit3 Debugger Programmer Emulator Controller Development Board is a compact in-circuit tool for developing with PIC and dsPIC Flash microcontrollers. It links to a host PC through a full-speed USB interface and reaches the target board through a 6-pin cable, so you can program and debug without removing the microcontroller from your circuit.

At roughly 95 mm long and 40 mm wide, the board is small enough to sit beside a breadboard or benchtop prototype. Three diagnostic LEDs report power, active and status conditions, which makes it easier to see what the tool is doing during a programming or debug session.

Key Features

  • Full-speed USB support using standard Windows drivers
  • Real-time execution, so processors can run at maximum speeds while debugging
  • Read and write access to program and data memory of the microcontroller
  • Erase of all memory types, including EEPROM, ID, configuration and program memory, with verification
  • Peripheral freeze at the breakpoint for closer inspection of behaviour
  • Built-in over-voltage and short-circuit monitor
  • Diagnostic LEDs for power, active and status

Specifications Explained

The 1.8V to 5V voltage rating is the target-side range. It means the tool can work with modern low-voltage PIC designs as well as traditional 5V circuits, without adding a separate level-shifting stage.

Flash support extends to 512K byte, which covers a broad set of PIC and dsPIC Flash microcontrollers used in control, sensing and interface projects. The tool reads and writes both program and data memory, and it can erase every memory type with verification so you can confirm a clean device before flashing new firmware.

Real-time execution and peripheral freeze at the breakpoint are the debugging essentials: your code runs at full speed until it reaches a breakpoint, and the peripherals hold their state so you can examine registers and timing without the target drifting.

Compatibility and Requirements

The board connects to a PC using a full-speed USB interface and standard Windows drivers. It is intended for use with the MPLAB Integrated Development Environment, which provides the graphical interface for programming and debugging. The target connection uses the supplied 6-pin cable. Target boards must operate within the 1.8V to 5V range.

Typical Uses

  • Programming and debugging PIC and dsPIC Flash microcontrollers during development
  • Learning embedded C and assembly on PIC experiments
  • Verifying configuration and EEPROM settings before production
  • Bench testing control, sensor and interface circuits

What's in the Box

  • 1 x PICkit3 Programmer
  • 1 x USB cable
  • 1 x 6-pin cable
Buy PICKit3 Pinout at low price

Quick specs

Voltage Rating (V)
1.8 to 5
Supply Voltage
1.8 ~ 5
Flash Memory (Kbytes)
512
Length (mm)
95
Width (mm)
40
Weight (g)
30
See all specifications