Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

This PPM encoder converts up to 8 PWM receiver channels into a single PPM signal for flight controllers like Pixhawk. It simplifies wiring and supports flexible power options via a jumper.

Key Highlights

  • Converts 8 PWM inputs to 1 PPM output
  • Compact 31.6 x 23 mm board weighs only 10 g
  • Includes 90 mm input and output cables
  • Jumper JP1 for flexible power configuration
  • Pre-configured for 8 channels, no programming needed
  • Works with Pixhawk and APM flight controllers

Ideal For

  • Drone builders using PWM receivers with Pixhawk or APM
  • FPV pilots simplifying wiring in multirotor builds
  • RC hobbyists upgrading to PPM-based flight controllers
  • Fixed-wing UAV enthusiasts needing PPM conversion
  • Electronics geeks learning about PPM encoding

Buying Tip

Check whether your receiver outputs PWM and your flight controller requires PPM; if so, this encoder is the simple solution.

Elecvora expert review

Our verdict

A practical, no-fuss solution for connecting PWM receivers to PPM-only flight controllers. It is small, light, and works out of the box for 8 channels.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Simple plug-and-play for standard 8-channel setups
  • Compact and lightweight design
  • Jumper provides power flexibility
  • Includes necessary cables

Cons

  • Requires AVR ISP programmer for advanced settings
  • No instructions included for jumper configuration
  • May vary in size and design from images

Best for

DIY drone builders using PWM receivers with Pixhawk or APM

Not ideal for

Pilots who need to change PPM signal inversion or fail-safe without extra tools

Specifications

Item TypeModule
Input Channel8 PWM channel
Output channel1 PPM channel
Cable Length90
PPM Encoder dimensionsAs per below
Length (mm)31.6
Width (mm)23
Weight (g)10
Shipping Weight0.015 kg
Shipping Dimensions6 × 5 × 2 cm

What's in the box

  • 1 x Pixhawk PPM Encoder Module
  • 1 x JR plug 10P input end cable
  • 1 x JR plug 4P output end cable

Frequently Asked Questions

What does this PPM encoder do?
It converts up to 8 PWM channels from a receiver into a single PPM sum signal, allowing you to connect a PWM receiver to a flight controller that only accepts PPM input.
Is it compatible with my Pixhawk flight controller?
Yes, it is designed for Pixhawk and APM flight controllers that use PPM input. Ensure your receiver outputs PWM.
How do I power the encoder and receiver?
The jumper JP1 determines power routing. Leave it in place if powering from the autopilot, or remove it if using a separate power source for the receiver or servos.
Can I change the PPM settings?
The firmware is pre-configured for 8 channels. To change settings like signal inversion or fail-safe values, you need an AVR ISP programmer.
What is included in the package?
You get the PPM encoder module, a 10-pin JR input cable, and a 4-pin JR output cable.
Why does my module look different from the picture?
The product may vary in two different sizes and designs, but the functionality remains the same.

Overview

The Pixhawk PPM Encoder Module is a small but essential accessory for drone builders who need to connect a PWM receiver to a flight controller that only accepts PPM input. Many flight controllers, including Pixhawk and APM, require a single PPM sum signal rather than individual PWM channels. This module takes up to eight PWM channels from your receiver and encodes them into one PPM stream, reducing cable clutter and simplifying your wiring.

Key Features

  • 8 PWM inputs to 1 PPM output: Combine all your receiver channels into a single signal wire.
  • Compact and lightweight: The board measures 31.6 x 23 mm and weighs just 10 g, so it won't weigh down your build.
  • Ready to use: The firmware is pre-configured for 8 channels, so no programming is required for standard operation.
  • Flexible power options: Jumper JP1 allows you to power the receiver and servos either from the autopilot or from a separate power source.
  • Complete with cables: Includes a 90 mm input cable with a 10-pin JR plug and a 4-pin JR output cable.

Specifications Explained

Input channels: The module accepts up to 8 PWM signals, which covers typical RC receivers used in multirotor and fixed-wing models.

Output: It provides one PPM sum signal on a single wire, plus ground and power lines, making connection to the flight controller straightforward.

Dimensions and weight: At 31.6 mm long, 23 mm wide, and 10 g, the module is easy to mount with double-sided tape or a small bracket.

Cable length: The 90 mm cables give you enough length to reach the receiver and flight controller without excess wiring.

Compatibility and Requirements

This encoder is designed for flight controllers that accept PPM input, such as Pixhawk and APM. It works with standard PWM receivers. Note that the product may vary in two different sizes and designs, but functionality is unaffected.

If you need to change settings such as inverting the PPM signal or adjusting fail-safe values, you will need an AVR ISP programmer to reprogram the module.

Typical Uses

Use this encoder when building a drone with a PWM receiver and a PPM-only flight controller. It is also handy for upgrading an existing model where you want to reduce wiring complexity. The module is suitable for multirotors, fixed-wing aircraft, and other RC vehicles that use PPM-based autopilots.

What's in the Box

  • 1 x Pixhawk PPM Encoder Module
  • 1 x JR plug 10P input end cable
  • 1 x JR plug 4P output end cable

Quick specs

Item Type
Module
Input Channel
8 PWM channel
Output channel
1 PPM channel
Cable Length
90
PPM Encoder dimensions
As per below
Length (mm)
31.6
See all specifications