Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The Radiomaster ER6 is a 2.4GHz ExpressLRS PWM receiver with six servo outputs, dual antennas and up to 100mW telemetry power. It also monitors receiver or flight battery voltage automatically, making fixed-wing setup simpler.

Key Highlights

  • Six PWM outputs for driving up to six servos directly
  • Dual 20cm high-sensitivity antennas for signal diversity
  • Telemetry power up to 100mW, adjustable via LUA
  • Automatic detection of receiver or external battery voltage
  • Wi-Fi firmware updates and WEBUI configuration support
  • One-piece molded shell measuring 43 x 25mm at 14.5g

Ideal For

  • Fixed-wing pilots building servo-driven aircraft
  • RC hobbyists moving to ExpressLRS 2.4GHz gear
  • Modelers who want built-in flight battery telemetry
  • Bot and RC project builders using PWM outputs
  • Pilots adding telemetry sensors through CRSF later

Buying Tip

Check that your transmitter or module runs 2.4GHz ExpressLRS before buying, since this receiver does not operate on 900MHz systems.

Elecvora expert review

Our verdict

The ER6 is a practical ExpressLRS receiver for fixed-wing pilots who want six servo outputs and useful voltage telemetry in one small unit. Its dual antennas, Wi-Fi configuration and CRSF expansion port make it a flexible building block for servo-based models.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Six PWM channels remove the need for a separate PWM board
  • Dual 20cm antennas and up to 100mW telemetry power
  • Automatic receiver or flight battery voltage telemetry
  • Wi-Fi updates and WEBUI configuration
  • Compact 14.5g one-piece molded shell

Cons

  • Requires a compatible 2.4GHz ExpressLRS transmitter or module
  • No 900MHz operation
  • Servos and a suitable power source are not included

Best for

Fixed-wing aircraft and servo-driven RC models using 2.4GHz ExpressLRS

Not ideal for

Pilots running 900MHz ExpressLRS systems or compact racing quad builds needing minimal wiring

Specifications

Item TypeELRS PWM Receiver
Power Supply Voltage (V)DC 4.5 - 8.4V
Antenna Type20cm high sensitivity dual antenna
Output channel6CH PWM
Power Ratingmaximum 100mw (LUA Adjustable) Telemetry Power
Detection rangeDC 4.0 - 35V
Length (mm)43
Width (mm)25
Weight (g)14.5
Shipping Weight0.024 kg
Shipping Dimensions9 × 5 × 3 cm

What's in the box

  • 1 x ER6 2.4GHz ELRS PWM Receiver
  • 1 x Voltage telemetry wire (Type-B)
  • 1 x CRSF wire
  • 1 x ELRS-RX-SBUS wire
  • 1 x User Card

Frequently Asked Questions

What is the Radiomaster ER6?
It is a 2.4GHz ExpressLRS PWM receiver with six output channels, dual 20cm antennas and telemetry power up to 100mW. It is aimed at fixed-wing and other servo-driven models.
Which transmitters work with the ER6?
The ER6 is compatible with all 2.4GHz ExpressLRS modules and transmitters that have 2.4GHz ExpressLRS built in. It does not operate on 900MHz ExpressLRS gear.
What voltage does the receiver need?
The ER6 accepts a DC supply from 4.5 to 8.4V. Its voltage telemetry can separately monitor an external battery from 4.0 to 35V and automatically detects which input to use.
How many servos can I connect?
There are six PWM output channels, so up to six servos can be connected directly. The unit uses 2.54mm connectors and includes voltage telemetry, CRSF and ELRS-RX-SBUS wires.
How do I update the firmware?
The receiver supports Wi-Fi updates and WEBUI configuration. Enable Wi-Fi on the unit, open the WEBUI, and follow the firmware update process for ExpressLRS.
What is included with the receiver?
The package contains the ER6 receiver, a Type-B voltage telemetry wire, a CRSF wire, an ELRS-RX-SBUS wire and a user card. Servos and a power source are not included.

Overview

The Radiomaster ER6 is a 2.4GHz ExpressLRS PWM receiver designed with fixed-wing aircraft and other servo-driven models in mind. Instead of a compact drone-style output, it offers six PWM channels so ailerons, elevator, rudder, throttle and auxiliary functions can connect in the traditional way. The board is built around ExpressLRS, which provides the configuration flexibility and response speed the system is known for.

A dual 20cm high-sensitivity antenna arrangement gives the receiver two signal paths, while telemetry power can be set as high as 100mW using LUA. The unit runs on a DC 4.5 to 8.4V supply and weighs just 14.5g, so it adds little mass to a model.

Key Features

  • Six PWM channels: connect up to six servos without an external PWM board.
  • Dual antennas: two 20cm high-sensitivity antennas for diversity.
  • Adjustable telemetry: telemetry power up to 100mW, configurable through LUA.
  • Voltage telemetry: monitors receiver voltage or an external flight battery from 4.0 to 35V and detects the active input automatically.
  • CRSF port: a four-wire CRSF interface is reserved for expanding telemetry sensors later.
  • Wi-Fi configuration: firmware updates and WEBUI setup are handled over Wi-Fi.
  • Sturdy shell: one-piece molding gives the 43 x 25mm case high structural strength.

Specifications Explained

The 4.5 to 8.4V input range covers common receiver power arrangements, so you can power the ER6 from a suitable DC source within that window. The separate 4.0 to 35V detection range is for voltage telemetry: the receiver can watch an external flight battery and report its level, switching automatically between the built-in receiver voltage and the external input.

Six PWM outputs are the practical heart of the unit. Each channel drives a standard servo connection, which keeps wiring simple on fixed-wing airframes. The 2.54mm connectors are a common size, and the supplied voltage telemetry, CRSF and ELRS-RX-SBUS wires cover the main connection options. At 43mm long, 25mm wide and 14.5g, the receiver fits into most radio compartments without crowding.

Compatibility and Requirements

The ER6 works with all 2.4GHz ExpressLRS modules and transmitters that have 2.4GHz ExpressLRS built in. It is a 2.4GHz receiver, so 900MHz ExpressLRS equipment is not part of its operating band. You will need a compatible ExpressLRS transmitter or module, a suitable DC power source within 4.5 to 8.4V, and servos for your model. Wi-Fi is used for firmware updates and WEBUI configuration.

Typical Uses

The six PWM outputs and voltage telemetry make the ER6 a natural fit for fixed-wing aircraft where several servos need direct control. It also suits other RC models and bots that use conventional PWM servo connections and benefit from telemetry feedback. The reserved CRSF port gives room to add sensors as a project grows.

What's in the Box

  • 1 x ER6 2.4GHz ELRS PWM Receiver
  • 1 x Voltage telemetry wire (Type-B)
  • 1 x CRSF wire
  • 1 x ELRS-RX-SBUS wire
  • 1 x User Card
RadioMaster ER6 2.4GHz ELRS PWM ReceiverRadioMaster ER6 2.4GHz ELRS PWM Receiver

Quick specs

Item Type
ELRS PWM Receiver
Power Supply Voltage (V)
DC 4.5 - 8.4V
Antenna Type
20cm high sensitivity dual antenna
Output channel
6CH PWM
Power Rating
maximum 100mw (LUA Adjustable) Telemetry Power
Detection range
DC 4.0 - 35V
See all specifications