Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 30A brushless speed controller running SimonK firmware, rated for 4V to 16.8V with a 35A burst and an onboard 5V BEC. Its fast 490Hz response and 16KHz motor frequency give smooth, quiet control on multirotors and planes.

Key Highlights

  • 30A continuous and 35A burst current handling
  • Works on 4V to 16.8V, covering 2S and 3S packs
  • Onboard 5V BEC powers the receiver without an extra battery
  • SimonK firmware with over 490Hz input response rate
  • 16KHz motor frequency for quiet, fast motor response
  • Compact 32 x 24mm body weighing about 25g

Ideal For

  • Multirotor builders working on 450 and X525 class frames
  • Pilots assembling small helicopter builds
  • Fixed-wing hobbyists needing a compact 30A ESC
  • RC car builders running high-speed brushless setups
  • Makers starting a first drone project on 2S or 3S power

Buying Tip

Confirm your motor's continuous current stays at or below 30A and your pack voltage falls within 4V to 16.8V before wiring the ESC in.

Elecvora expert review

Our verdict

A straightforward 30A ESC that suits small multirotors and planes where simple, fast throttle response matters more than programmable features. The onboard BEC and SimonK firmware make wiring and setup easy for builders who want to get flying quickly.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Fast, buffer-free signal response from SimonK firmware
  • Onboard 5V BEC removes the need for a receiver battery
  • No cutoff behaviour that could drop a multirotor mid-flight
  • Compact 25g body fits tight frame layouts

Cons

  • Limited to 4V to 16.8V, so not for higher cell counts
  • No programmable settings beyond throttle range
  • Requires soldering and correct polarity during installation

Best for

Small multirotor, helicopter and airplane builds on 2S or 3S power

Not ideal for

Large builds drawing well over 30A or running higher-voltage packs

Specifications

Item TypeBrushless ESC
Model No. / NameSimonK 30A Brushless Speed Controller ESC
Voltage Rating (V)4 V-16.8V
Constant Current (A)30
Burst Current (A)35
BEC (Y/N)Yes
ColorBlack
Length (mm)32
Width (mm)24
Weight (g)25
Shipping Weight0.018 kg
Shipping Dimensions8 × 8 × 5 cm

What's in the box

  • 1 x SimonK 30A Brushless Speed Controller ESC

Frequently Asked Questions

What battery voltage does this ESC support?
It accepts 4V to 16.8V, which covers 2S and 3S lithium packs. Check your pack's full charge voltage against this range before connecting.
Does it need a separate receiver battery?
No. The onboard BEC supplies 5V to the receiver, so an extra receiver battery is not required.
How much current can it handle?
It is rated for 30A continuous with a 35A burst rating for short peaks. Keep your motor's normal draw within the continuous figure.
Do I need to program it?
No. The only adjustment is setting the throttle range; there are no other settings to program.
Why does it have no low-voltage cutoff?
A cutoff on a multirotor would mean a sudden loss of power and a crash, so this ESC keeps driving the motor instead of cutting out.
What is included in the package?
One SimonK 30A Brushless Speed Controller ESC. Motors, propellers, batteries and wiring are not included.

Overview

The SimonK 30A Brushless Speed Controller is a single-motor ESC for multirotor, helicopter and fixed-wing builds. It drives brushless motors drawing up to 30A continuously, with a 35A burst rating for short peaks. The input range of 4V to 16.8V covers common 2S and 3S lithium packs, making it a practical choice for small and mid-size airframes.

It runs SimonK firmware, a firmware choice valued by multirotor builders for quick signal handling. The controller also includes an onboard BEC that supplies 5V to the receiver, so a separate receiver battery is not required.

Key Features

  • SimonK firmware: fast, buffer-free input handling for responsive throttle changes.
  • 100% N-FET design: efficient power switching across the current range.
  • Crystal oscillator: keeps the PWM operating range stable as temperature changes.
  • No low-voltage cutoff: avoids an in-flight shutdown on a multirotor.
  • No over-temperature cutoff: the ESC keeps working instead of cutting power mid-flight.
  • 16KHz motor frequency: fast motor response with quieter operation.
  • Simple setup: nothing to program beyond the throttle range.

Specifications Explained

30A continuous, 35A burst: the ESC is sized for motors that draw around 30A in normal flight, with headroom for brief current spikes.

4V to 16.8V input: this matches 2S and 3S lithium packs. Check your pack voltage against this range before connecting.

5V BEC: the built-in battery eliminator circuit feeds the receiver, simplifying wiring and saving weight.

Response rate above 490Hz: the input signal is not buffered, so throttle commands reach the motor quickly.

32 x 24mm, 25g: a small footprint that fits tight multirotor arms and narrow fuselages.

Compatibility and Requirements

The ESC works with brushless motors within its 30A continuous rating and with receiver signals in the supported input range. It is suited to 450, F650 and X525 quadcopters as well as other airplanes and high-speed RC cars. Because the BEC supplies the receiver, plan your wiring so the receiver is powered from the ESC's 5V line. When the ESC is connected directly to a receiver, always switch off power to the ESC before switching off the transmitter; on some radio models doing the reverse can apply full throttle to the motor.

Typical Uses

  • 450, F650 and X525 class quadcopters
  • Small multirotor and helicopter builds
  • Fixed-wing airplanes
  • High-speed RC cars

What's in the Box

1 x SimonK 30A Brushless Speed Controller ESC. Motors, propellers, batteries and wiring shown in reference images are not included.

Quick specs

Item Type
Brushless ESC
Model No. / Name
SimonK 30A Brushless Speed Controller ESC
Voltage Rating (V)
4 V-16.8V
Constant Current (A)
30
Burst Current (A)
35
BEC (Y/N)
Yes
See all specifications