Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 30.5×30.5mm F7 flight controller with STM32F722, BMI270 and BMP280, plus built-in Wi-Fi and Bluetooth for wireless configuration. It runs on 3S–6S LiPo and offers five UART sets, including a dedicated ESC telemetry UART.

Key Highlights

  • STM32F722 MCU with BMI270 IMU and BMP280 barometer
  • Built-in 2.4 GHz Wi-Fi and Bluetooth combo chip for wireless setup
  • Five UART sets including UART4 for ESC telemetry
  • 3S–6S LiPo input with USB Type-C and AT7456E OSD
  • 30.5×30.5mm mounting with 4mm holes, 41×38mm board
  • Light 10.7g board with a full cable set included

Ideal For

  • FPV racing pilots building lightweight 5-inch quads
  • Freestyle pilots who tune frequently at the field
  • Builders using 30.5×30.5mm stacks with 3S–6S power
  • Pilots who want wireless configuration from a phone
  • Makers adding GPS, receiver and VTX to one board

Buying Tip

Check that your frame uses a 30.5×30.5mm mounting pattern with 4mm holes and that your ESC and receiver match the included cable types before ordering.

Elecvora expert review

Our verdict

The SpeedyBee F7 V3 packs an F7 processor, dual sensors and wireless configuration into a compact 30.5×30.5mm board with a generous cable set. It is a practical choice for pilots who tune often and want a clean, well-connected stack.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • STM32F722 MCU with BMI270 IMU and BMP280 barometer
  • Built-in Wi-Fi and Bluetooth for wireless configuration
  • Five UARTs with a dedicated ESC telemetry port
  • Compact 41×38mm board at 10.7g
  • Comprehensive cable and grommet kit included

Cons

  • Requires a separate receiver, ESC, camera and VTX to complete a build
  • Analogue OSD chip means digital OSD depends on your video system
  • No battery or power distribution board included

Best for

Racing and freestyle pilots building 3S–6S quads on a 30.5×30.5mm stack

Not ideal for

Builders who need a plug-and-play kit with motors, ESCs and video gear included

Specifications

Item TypeFlight Controller
MCU TypeSTM32F722
IMU sensorBMI270
USBType-C
BarometerBMP280
OSD ChipAT7456E chip
Bluetooth VersionSupported.Used for Flight Controller configuration, built in a single 2.4 GHz Wi-Fi and Bluetooth combo chip
Mounting Hole Diameter (mm)30.5 * 30.5mm(4mm hole diameter)
UART5 sets( UART1, UART 2,UART 3, UART 4(For ESC Telemetry), UART 6)
Input Power (W)3S - 6S Lipo
ESC Telemetry UARTR4(UART4)
Length (mm)41
Width (mm)38
Weight (g)10.7
Shipping Weight0.072 kg
Shipping Dimensions12 × 5.8 × 3 cm

What's in the box

  • 1 × SpeedyBee F7 V3 Flight Controller
  • 1 × DJI 6-pin cable (80mm)
  • 1 × SH 1.0mm 8-pin cable, 30mm (FC to ESC)
  • 5 × M3×8mm silicone grommets
  • 1 × 4-pin SH1.0 to 3+2-pin JST1.25 FPV camera cable (30mm)
  • 1 × 4-pin SH1.0 to 3+2-pin JST1.25 FPV camera cable (60mm)
  • 1 × 4-pin SH1.0 to 4-pin JST1.25 FPV camera cable (60mm)
  • 1 × 4-pin SH1.0 radio receiver cable (100mm)
  • 1 × 4-pin SH1.0 to 4-pin SH1.0 analogue VTX cable
  • 1 × 6-pin SH1.0 GPS module cable, open end (100mm)
  • 1 × 6-pin SH1.0 GPS module cable with connector

Frequently Asked Questions

What voltage can the SpeedyBee F7 V3 accept?
The board is rated for 3S–6S LiPo input. Stay within that range when connecting power.
How do I configure the board without a USB cable?
The built-in 2.4 GHz Wi-Fi and Bluetooth combo chip supports wireless configuration from a phone. USB Type-C is also available for wired setup.
How many UARTs does it have?
It provides five UART sets: UART1, UART2, UART3, UART4 and UART6. UART4 is designated for ESC telemetry.
What mounting pattern does it use?
It uses a 30.5×30.5mm mounting pattern with 4mm holes, and the board measures 41×38mm and weighs 10.7g.
What is included in the box?
You get the flight controller, a DJI 6-pin cable, an FC-to-ESC cable, five silicone grommets, several FPV camera and VTX cables, a receiver cable and two GPS module cables.
Does it support on-screen display?
Yes, it uses an AT7456E OSD chip for analogue on-screen display. The included DJI 6-pin cable is provided for digital video connections.

Overview

The SpeedyBee F7 V3 is a flight controller for multirotor builds that need a fast F7-class processor in a standard 30.5×30.5mm footprint. The STM32F722 MCU handles flight loop and peripheral duties, while the BMI270 IMU provides motion sensing and the BMP280 barometer adds altitude data. An AT7456E chip drives analogue on-screen display, so key flight information can be shown through your video feed.

What sets this board apart is its wireless configuration: a single 2.4 GHz Wi-Fi and Bluetooth combo chip lets you connect from a phone for setup, reducing the need to plug in a USB cable every time you change a setting. When you do want a wired connection, the USB Type-C port is there.

Key Features

  • STM32F722 MCU for responsive flight performance in racing and freestyle builds.
  • BMI270 IMU paired with a BMP280 barometer for motion and altitude sensing.
  • Wireless configuration through the built-in 2.4 GHz Wi-Fi and Bluetooth combo chip.
  • Five UART sets: UART1, UART2, UART3, UART4 (ESC telemetry) and UART6.
  • 3S–6S LiPo input to match common racing and freestyle power setups.
  • AT7456E OSD chip for on-screen display through an analogue video system.
  • Compact 41×38mm board weighing 10.7g, with 30.5×30.5mm mounting and 4mm holes.

Specifications Explained

The MCU and IMU are the core of any flight controller. The STM32F722 is an F7-series processor, and the BMI270 is the gyro and accelerometer that reports how the craft moves. Together they form the control loop that keeps the quad stable. The BMP280 barometer gives the board pressure-based altitude information, which is useful for altitude-related features in supported firmware.

Five UART sets give you room to connect a receiver, GPS module, VTX control and other peripherals at the same time. UART4 is designated for ESC telemetry, so you can route ESC data back to the controller without giving up another port. The AT7456E chip handles OSD, meaning analogue video setups can display flight data on the feed.

The 30.5×30.5mm mounting pattern with 4mm holes is a common stack standard, and the 41×38mm board size keeps the footprint tight. Power input is rated for 3S–6S LiPo, covering a broad range of multirotor builds.

Compatibility and Requirements

The board is designed for 3S–6S LiPo input and uses a USB Type-C connection for wired setup. Wireless configuration uses the integrated 2.4 GHz Wi-Fi and Bluetooth combo chip. The OSD chip supports analogue on-screen display, and the included DJI 6-pin cable is provided for digital video connections. You will need a compatible receiver, ESC, camera and video transmitter to complete a build; these are not included.

Typical Uses

With its F7 processor, compact size and wireless setup, the F7 V3 suits racing quads and freestyle builds where quick tuning at the field is valuable. The five UARTs and dedicated ESC telemetry port make it practical for builds that carry GPS, a receiver and a VTX. Its 30.5×30.5mm mounting fits many standard frames, and the 10.7g weight keeps the stack light.

What's in the Box

  • 1 × SpeedyBee F7 V3 Flight Controller
  • 1 × DJI 6-pin cable (80mm)
  • 1 × SH 1.0mm 8-pin cable, 30mm (FC to ESC)
  • 5 × M3×8mm silicone grommets
  • 2 × 4-pin SH1.0 to 3+2-pin JST1.25 FPV camera cables (30mm and 60mm)
  • 1 × 4-pin SH1.0 to 4-pin JST1.25 FPV camera cable (60mm)
  • 1 × 4-pin SH1.0 radio receiver cable (100mm)
  • 1 × 4-pin SH1.0 to 4-pin SH1.0 analogue VTX cable
  • 1 × 6-pin SH1.0 GPS module cable, open end (100mm)
  • 1 × 6-pin SH1.0 GPS module cable with connector

Quick specs

Item Type
Flight Controller
MCU Type
STM32F722
IMU sensor
BMI270
USB
Type-C
Barometer
BMP280
OSD Chip
AT7456E chip
See all specifications