
1 / 4 · Click to enlarge
AI Summary
An isolated in-circuit debugger and programmer for STM8 and STM32 microcontrollers, connecting to your PC over USB and to the target through JTAG, SWD or SWV. Its 1000 Vrms isolation keeps the host and target sides safely separated during debugging and programming.
Key Highlights
- 1000 Vrms isolation between the PC and target application board
- Supports STM8 and STM32 microcontroller families
- JTAG, SWD and Serial Wire Viewer protocol support
- USB 2.0 full-speed interface with 5 V bus power
- Direct Firmware Update over USB via DFU
- Status LEDs indicate communication activity
Ideal For
- Embedded firmware engineers working with STM8 and STM32 microcontrollers
- Development teams debugging boards that require PC-to-target isolation
- Electronics students and educators learning ST microcontroller toolchains
- Repair and test technicians flashing ST-based control boards
- Hardware labs needing a reliable in-circuit programming link
Buying Tip
Confirm that your target board exposes a JTAG, SWD or SWIM header and that your toolchain supports the ST-LINK/V2-ISOL before ordering, since the debugger connects through those interfaces only.
Elecvora expert review
Our verdict
A purpose-built isolated debug probe that removes a common pain point in STM8 and STM32 development. The 1000 Vrms barrier and multi-protocol support make it a sensible choice for labs where the PC and target should stay electrically separate.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- 1000 Vrms isolation between host and target
- Supports JTAG, SWD and SWV in one unit
- Works across STM8 and STM32 families
- USB-powered with no external supply needed
- DFU firmware updates over USB
Cons
- Limited to STM8 and STM32 targets
- Requires a host PC with a USB port
- Only rated for 0 to 50 °C operation
Best for
Engineers debugging STM8 and STM32 boards that need PC-to-target isolation
Not ideal for
Developers working with microcontrollers outside the STM8 and STM32 families
Specifications
| Interface | USB 2.0 Full-Speed Compatible |
|---|---|
| Power Supply Voltage (V) | 5V via USB Connector |
| Firmware Compatible | Direct Firmware Update (DFU) Supported |
| Operating Temperature (°C) | 0 to 50 |
| Supported protocols | JTAG, SWD, Serial Wire Viewer (SWV) |
| Shipping Weight | 0.122 kg |
| Shipping Dimensions | 13 × 11 × 5 cm |
What's in the box
- 1 x ST-LINK/V2-ISOL Debugger
- 1 x USB Standard A to Mini-B Cable
- 1 x SWIM and JTAG Cables for Connection
Frequently Asked Questions
Which microcontrollers does this debugger support?
How is the debugger powered?
What does the 1000 Vrms isolation mean for me?
Can I update the debugger firmware?
What cables come with the unit?
What operating temperature is supported?
Overview
The STMicroelectronics ST-LINK/V2-ISOL is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. It sits between a host PC and the target application board, giving developers a hardware link for flashing firmware, stepping through code and inspecting signals. The isolated design places 1000 Vrms of separation between the PC side and the target side, which is valuable when the application board runs at elevated voltages or when ground loops would otherwise disturb measurements.
The unit is powered from the USB connector at 5 V and uses a USB 2.0 full-speed interface, so no separate power supply is required. Status LEDs blink during communication, giving immediate feedback that a session is active.
Key Features
- Isolated architecture: 1000 Vrms isolation protects the host PC from the target board.
- Multi-protocol support: works with JTAG, SWD and Serial Wire Viewer (SWV).
- Broad MCU coverage: designed for STM8 and STM32 microcontroller families.
- USB 2.0 full-speed: simple, reliable connection to the development machine.
- DFU firmware updates: keep the debugger firmware current directly over USB.
- Visual feedback: status LEDs indicate communication activity.
Specifications Explained
Isolation voltage
The 1000 Vrms rating describes the separation maintained between the PC interface and the target interface. In practice this means you can debug a board whose circuitry sits at a different potential from the PC without creating a direct electrical path between them.
Supported protocols
JTAG and SWD are the standard debug interfaces used across the STM32 range, while SWV provides a trace channel for real-time visibility. Supporting all three gives flexibility across different target boards and toolchains.
Power and interface
The debugger draws its 5 V supply from the USB connector and communicates over USB 2.0 full-speed, so a standard host port is sufficient. It is rated for operation between 0 and 50 °C.
Compatibility and Requirements
The ST-LINK/V2-ISOL is intended for STM8 and STM32 microcontroller families and supports JTAG, SWD and SWV connections. A host PC with a USB port is required, along with the appropriate SWIM and JTAG cables supplied in the box. Firmware updates are performed over USB using DFU.
Typical Uses
- Programming and debugging STM8 and STM32 microcontroller projects
- Embedded system development where isolation between PC and target is needed
- Firmware flashing and in-circuit testing on production or prototype boards
- Laboratory and educational work with ST microcontroller platforms
What's in the Box
- 1 x ST-LINK/V2-ISOL debugger
- 1 x USB standard A to Mini-B cable
- 1 x SWIM and JTAG cable set for connection
Quick specs
- Interface
- USB 2.0 Full-Speed Compatible
- Power Supply Voltage (V)
- 5V via USB Connector
- Firmware Compatible
- Direct Firmware Update (DFU) Supported
- Operating Temperature (°C)
- 0 to 50
- Supported protocols
- JTAG, SWD, Serial Wire Viewer (SWV)
- Shipping Weight
- 0.122 kg


















