Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact PCB adapter that maps a 20-pin 2.54mm JTAG header to a 4-pin SWD interface for JLINK programmers. Its small 31 x 19.8mm footprint and 4.9g weight make it easy to keep on the bench or in a dev kit.

Key Highlights

  • 20-pin 2.54mm pitch JTAG input with 4-pin SWD output
  • Designed for use with JLINK programmers
  • Compact PCB footprint of 31mm by 19.8mm
  • Weighs approximately 4.9g for easy integration
  • Suits ARM Cortex MCU debugging and firmware flashing
  • Standard PCB construction with a simple fixed pin mapping

Ideal For

  • Embedded engineers debugging ARM Cortex MCU boards
  • Firmware developers flashing SWD-capable targets
  • Hardware technicians running bench diagnostics
  • Makers building compact JLINK-based workstations
  • Students learning SWD programming workflows

Buying Tip

Check that your JLINK programmer uses a 20-pin 2.54mm JTAG header and that your target board exposes a 4-pin SWD port before ordering.

Elecvora expert review

Our verdict

A simple, well-sized adapter that solves the common mismatch between a 20-pin JTAG programmer and a 4-pin SWD target. It is a practical bench accessory rather than a feature-rich tool, and that is exactly what most developers need.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Clear 20-pin to 4-pin SWD conversion
  • Very small and light for crowded benches
  • Standard PCB construction keeps it simple
  • Specified for JLINK programmers

Cons

  • Cables and target connections are not included
  • No active buffering or isolation is specified
  • Only suits devices with an SWD interface

Best for

Developers connecting JLINK programmers to SWD-capable ARM Cortex boards

Not ideal for

Users who need a full JTAG-to-JTAG or isolated debug solution

Specifications

Item TypeAdapter Board
Model No. / NameSWD to JTAG adapter board
InterfaceJTAG to SWD
CompatibilityJLINK programmers
MaterialStandard PCB
Length (mm)31
Width (mm)19.8
Weight (g)4.9
Shipping Weight0.005 kg
Shipping Dimensions5 × 3 × 2 cm

What's in the box

  • 1 x SWD to JTAG adapter board

Frequently Asked Questions

What does this adapter board do?
It converts a 20-pin 2.54mm JTAG connection into a 4-pin SWD interface so a JLINK programmer can reach an SWD-capable target.
Which programmers is it compatible with?
The product data specifies compatibility with JLINK programmers. Check your programmer's header before use.
Does it work with ARM Cortex MCUs?
Yes, it is intended for ARM Cortex debugging and other SWD-supported devices, provided the target exposes an SWD port.
Are cables included?
The package contains the adapter board only. JTAG and SWD cables or connections must be supplied separately.
Does the board need external power?
It is a passive standard PCB adapter, so it does not require its own power supply. Power the target board according to its own requirements.
How should I store and handle it?
Keep it in an antistatic bag or a dry parts box, and avoid bending the header pins when plugging and unplugging cables.

Overview

This SWD to JTAG adapter board is a small interface PCB that bridges a 20-pin, 2.54mm pitch JTAG header and a 4-pin SWD connection. It is built for developers who use JLINK programmers and need a tidy, repeatable way to reach the Serial Wire Debug port on a target board. Instead of assembling a custom cable, you plug into the 20-pin side and take the 4-pin SWD output to your device.

At 31mm long, 19.8mm wide and about 4.9g, the board takes up very little room on a workbench or inside a development setup. The standard PCB construction keeps the design simple and the signal path short.

Key Features

  • 20-pin JTAG interface at 2.54mm pitch
  • 4-pin SWD output for JLINK compatibility
  • Compact 31 x 19.8mm board size
  • Lightweight at roughly 4.9g
  • Simple integration into existing debug setups
  • Intended for ARM Cortex debugging and related SWD devices

Specifications Explained

20-pin 2.54mm JTAG interface

The 20-pin side matches the common 2.54mm pitch JTAG header layout, so it connects to standard ribbon cables and headers used with JLINK programmers. The 2.54mm pitch is the familiar through-hole spacing found on many development boards.

4-pin SWD output

The output side reduces the connection to four SWD pins, which is the compact debug interface used by many ARM Cortex microcontrollers. This reduction keeps the cable run to the target short and simple.

Size and weight

With a 31mm by 19.8mm footprint and a weight of about 4.9g, the adapter adds almost nothing to a tool bag and can sit close to the target board without strain on the connectors.

Compatibility and Requirements

The adapter is specified for JLINK programmers and for SWD-supported devices, including ARM Cortex MCUs. A suitable JTAG cable for the 20-pin side and a 4-pin SWD connection to the target are required but not included. Confirm that your target board exposes an SWD header before use.

Typical Uses

  • Firmware flashing during development
  • Debugging ARM Cortex MCU projects
  • Hardware diagnostics on SWD-capable boards
  • Bench setups where a short, fixed adapter is preferred

What's in the Box

1 x SWD to JTAG adapter board with a 20-pin 2.54mm JTAG interface and a 4-pin SWD output.

Quick specs

Item Type
Adapter Board
Model No. / Name
SWD to JTAG adapter board
Interface
JTAG to SWD
Compatibility
JLINK programmers
Material
Standard PCB
Length (mm)
31
See all specifications