Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 5 VDC driver board with a 20 mm ultrasonic atomizing disc on a 70 mm cable, built for small DIY mist and humidifier projects. It produces fine droplets quietly at around 113 KHz with a 2.5 W power rating.

Key Highlights

  • 5 VDC operating voltage suits USB-based power sources
  • 20 mm oscillator disc on a 70 mm cable
  • 113 KHz nominal operating frequency for fine mist
  • 2.5 W power rating for low-demand builds
  • Stable waveform and low impedance driver design
  • Wide -30 to +85 °C operating temperature range

Ideal For

  • Makers building small DIY humidifiers
  • Model and diorama builders adding mist effects
  • Hobbyists repairing 20 mm atomizer modules
  • Prop and high-end toy developers
  • Electronics learners practising low-voltage wiring

Buying Tip

Check that your power source delivers a steady 5 VDC and that your reservoir opening suits a 20 mm disc before wiring the board in.

Elecvora expert review

Our verdict

A straightforward, low-cost atomizer module that does one job well: turning 5 VDC into fine mist from a 20 mm disc. It suits builders who already understand basic wiring and want a compact mist source rather than a finished product.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Simple 5 VDC input
  • Compact 20 mm oscillator
  • Quiet ultrasonic operation
  • Cable separates board from water
  • Low 2.5 W power draw

Cons

  • Bare component, no enclosure or reservoir
  • Requires correct polarity and dry wiring
  • Output depends on disc placement at the water surface

Best for

Small DIY humidifiers and mist-effect projects

Not ideal for

Buyers wanting a ready-to-use appliance

Specifications

Operating Voltage (VDC)5
Operating Temperature (°C)-30 ~ +85
Operating Frequency (KHz)113 - 3KHz
Power Rating2.5
Diameter (mm)Oscillator:20
Cable LengthOscillator: 70
Shipping Weight0.02 kg
Shipping Dimensions9 × 10 × 2 cm

What's in the box

  • 1 x USB Ultrasonic Humidifier Power Circuit Board with Atomizing Chip
  • 1 x 20 mm oscillator disc on 70 mm cable

Frequently Asked Questions

What voltage does this board need?
It is specified for 5 VDC operation. Use a supply that matches this figure and keep the wiring dry.
What size atomizing disc does it use?
It is designed for an oscillator disc of 20 mm diameter, connected by a 70 mm cable.
Can I use it as a complete humidifier?
No. It is a driver board and disc set, so you still need a power source, a water reservoir and a housing.
How much power does it draw?
The power rating is 2.5 W, which is low enough for small builds and modest supplies.
What is included in the package?
One USB ultrasonic humidifier power circuit board with atomizing chip and the 20 mm oscillator on its cable.
How should I care for the module?
Keep the board dry, avoid running the disc without water, and disconnect power before cleaning or repositioning the disc.

Overview

This is a two-part ultrasonic atomizing set: a small driver board and a piezoelectric disc mounted on a 70 mm cable. Feed the board from a 5 VDC supply and it oscillates the disc at around 113 KHz, producing the rapid pressure changes that break water into a fine mist. It is a bare component intended for building or repairing small mist devices, not a plug-and-play humidifier.

Key Features

  • USB-friendly input: runs from a 5 VDC supply, matching common USB power arrangements.
  • Compact atomizer: the 20 mm oscillator disc fits small reservoirs and tight enclosures.
  • Remote mounting: the 70 mm cable lets the board sit away from the water while the disc does the work.
  • Quiet operation: ultrasonic cavitation generates mist with low acoustic noise.
  • Stable drive: low impedance and a stable waveform support consistent atomization.
  • Wide temperature range: rated for -30 to +85 °C operating conditions.

Specifications Explained

Operating voltage: 5 VDC is the input the board expects. Match your supply to this figure rather than assuming a higher voltage is fine.

Operating frequency: the 113 KHz band is where the disc resonates to create cavitation. The atomizing chip is tuned to this range, so the disc and board should be kept together as a matched pair.

Power rating: 2.5 W is modest, which keeps heat and supply demands low for small builds.

Oscillator size: the 20 mm diameter defines the mist output scale and the opening you need in your reservoir or housing.

Cable length: 70 mm gives a little separation between the electronics and the wet side.

Compatibility and Requirements

The board is designed for an atomization disc of 20 mm diameter, so replacement discs should match that size. You need a 5 VDC power source and basic wiring to connect the board; a USB connection is implied by the product type, but confirm your own supply arrangement. No enclosure, reservoir or switch is included.

Typical Uses

  • Miniature and desktop humidifier builds
  • Model scenery, dioramas and display mist effects
  • High-end toy and prop projects needing a small mist source
  • Repair or replacement of an existing 20 mm atomizer module

What's in the Box

One USB ultrasonic humidifier power circuit board with atomizing chip, including the 20 mm oscillator on its 70 mm cable.

Quick specs

Operating Voltage (VDC)
5
Operating Temperature (°C)
-30 ~ +85
Operating Frequency (KHz)
113 - 3KHz
Power Rating
2.5
Diameter (mm)
Oscillator:20
Cable Length
Oscillator: 70
See all specifications