Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A Raspberry Pi HAT built on the A7670E module that adds LTE Cat-1, GSM/GPRS data, calls and SMS plus GPS, BeiDou and GLONASS positioning. Its 40-pin header, SIM slot and audio jack make connected tracking and monitoring projects straightforward.

Key Highlights

  • A7670E LTE Cat-1 module with GSM, GPRS and EDGE support
  • GPS, BeiDou and GLONASS multi-constellation positioning onboard
  • Standard Raspberry Pi 40-pin GPIO header for Pi series boards
  • TCP/IP, HTTP(s), MQTT(s), FTP(s) and SSL protocol support
  • Onboard USB port and 3.5 mm audio jack for testing and calls
  • Breakout control pins for Arduino and STM32 host boards

Ideal For

  • Raspberry Pi makers building cellular-connected IoT devices
  • Engineers prototyping remote monitoring and diagnostic units
  • Developers adding GPS, BeiDou and GLONASS tracking to a project
  • Students learning AT commands, SMS and voice on embedded hardware
  • Integrators building POS or industrial router prototypes

Buying Tip

Check that your region and carrier support the A7670E LTE bands and that you have a 1.8V or 3V USIM card ready before powering the board.

Elecvora expert review

Our verdict

A tidy, well-documented HAT that combines cellular data, voice and multi-constellation positioning on one board. It suits telemetry and tracking builds where Cat-1 bandwidth is enough and the Raspberry Pi header saves wiring time.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Cellular data, calls, SMS and GNSS on a single HAT
  • Standard 40-pin header plus breakout pins for other hosts
  • Onboard USB and audio jack simplify testing and voice work
  • Protocol support covers HTTP, MQTT, FTP and SSL

Cons

  • Requires a separate USIM card and 5V supply
  • Cat-1 rates are not intended for high-bandwidth video
  • Host board and antennas must be sourced separately

Best for

Raspberry Pi and embedded developers building connected tracking, monitoring or POS prototypes

Not ideal for

Projects needing high-speed LTE video streaming or a fully enclosed plug-and-play unit

Specifications

Item TypeHAT
CompatibilityPi Series
HAT TypeGSM HAT, GPRS HAT
GNSSGPS, BeiDou, GLONASS
Storage CapacityUSIM card (CB couldn't be stored on SIM card)
Audio input/output PortStandard 3.5mm audio jack for audio input/output
Power Supply Voltage (V)5
Operating Voltage (V)3.3
Shipping Weight0.160 kg
Shipping Dimensions15 × 11 × 5 cm

What's in the box

  • 1 x Waveshare Cat-1/GSM/GPRS/GNSS HAT for Raspberry Pi, Based On A7670E module, LTE

Frequently Asked Questions

Which boards can I use this HAT with?
It uses the standard Raspberry Pi 40-pin GPIO header and supports Raspberry Pi series boards. Its breakout control pins also allow connection to hosts such as Arduino and STM32, and the resources include examples for Jetson Nano as well.
Does it support GPS and other satellite systems?
Yes. The board supports GPS, BeiDou and GLONASS positioning, and it can also use LBS base station positioning to obtain approximate location from the mobile network.
What power does the board need?
The board is supplied at 5V with a 3.3V operating voltage for logic. Plan for a stable 5V supply, since the cellular module draws current during transmission.
Can I make calls and send SMS with it?
Yes. The module supports dial-up, telephone calls and SMS, and the 3.5 mm audio jack lets you record audio, make calls and listen to TTS speech in Chinese or English.
What SIM card does it take?
The onboard slot accepts 1.8V and 3V USIM cards. Note that CB messages cannot be stored on the SIM card, so the module's own storage handles that.
What is included in the package?
The package contains one Waveshare Cat-1/GSM/GPRS/GNSS HAT based on the A7670E module, plus development resources and a manual. Raspberry Pi boards, SIM cards, antennas and power supplies are not included.

Overview

The Waveshare A7670E Cat-1 HAT is a cellular and positioning add-on board for Raspberry Pi and other host platforms. At its centre is the A7670E LTE Cat-1 module, which handles LTE-TDD, LTE-FDD, GSM, GPRS and EDGE wireless modes. That combination lets a project send and receive data over a mobile network, place and answer calls, and exchange SMS messages, while the same board also provides satellite positioning through GPS, BeiDou and GLONASS.

The board uses the standard Raspberry Pi 40-pin GPIO extension header, so it seats directly on Pi series boards. Common control pins of the A7670E module are broken out as well, which makes it possible to wire the module to hosts such as Arduino or STM32 boards. A 1.8V/3V SIM card slot, two status LEDs, an onboard USB interface and a 3.5 mm audio jack round out the hardware.

Key Features

  • Cellular data: LTE Cat-1 with GSM, GPRS and EDGE fallback modes.
  • Positioning: GPS, BeiDou and GLONASS support, plus LBS base station positioning for approximate location from the mobile network.
  • Protocol stack: TCP/IP, HTTP(s), MQTT(s), FTP(s) and SSL.
  • Voice and messaging: dial-up, telephone calls, SMS and TTS text-to-speech in Chinese and English.
  • Host flexibility: 40-pin Pi header plus breakout pins for Arduino and STM32.
  • Diagnostics: onboard USB port for AT command testing and network communication.

Specifications Explained

The A7670E module delivers Cat-1 LTE rates, which are well suited to telemetry and control traffic rather than video streaming. GSM and GPRS modes keep the link usable on older networks. The SIM slot accepts 1.8V and 3V USIM cards; note that the module's own storage is separate, since CB messages cannot be stored on the SIM card.

Power is supplied at 5V with a 3.3V operating voltage for logic, matching the Raspberry Pi header. The 3.5 mm jack carries audio in and out for calls, recording and playback of TTS output. Two LED indicators show operating status at a glance, and the exposed control pins let you integrate the module with non-Pi hosts.

Compatibility and Requirements

The HAT fits Raspberry Pi series boards through the standard 40-pin header. Development resources and a manual include examples for Raspberry Pi, Jetson Nano, Arduino and STM32, and the module supports Windows and Linux operating systems. A USIM card and a suitable 5V supply are required for cellular operation, and the host board is not included.

Typical Uses

  • Remote information processing and telemetry
  • Monitoring devices and remote diagnosis
  • POS terminals and industrial routers
  • Satellite positioning and asset tracking
  • Call, SMS and TTS projects on Raspberry Pi

What's in the Box

One Waveshare Cat-1/GSM/GPRS/GNSS HAT for Raspberry Pi, based on the A7670E module. Raspberry Pi, Jetson Nano, Arduino and STM32 host boards, SIM cards and power supplies are not included.

Quick specs

Item Type
HAT
Compatibility
Pi Series
HAT Type
GSM HAT, GPRS HAT
GNSS
GPS, BeiDou, GLONASS
Storage Capacity
USIM card (CB couldn't be stored on SIM card)
Audio input/output Port
Standard 3.5mm audio jack for audio input/output
See all specifications