
1 / 2 · Click to enlarge
At a glance
Made by WAVESHARE, this iot development boards is a good fit for makers, students and electronics hobbyists. Main specs: interface USB Type-C; controller ESP32-S3; input voltage (v) 5V. Check that your power source supplies 5V before connecting it.
Key Highlights
- Wireless connection
- Interface: USB Type-C
- Controller: ESP32-S3
- Input Voltage (V): 5V
Ideal For
- Arduino, ESP32 and Raspberry Pi projects
- School and college lab work
- Prototypes and test rigs
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Interface | USB Type-C |
|---|---|
| Controller | ESP32-S3 |
| Input Voltage (V) | 5V |
| GPIO | Multiple General Purpose Input/Output pins |
| Processor | 32-bit LX7 dual-core |
| Flash Memory | 16 MB |
| WiFi (Y/N) | IEEE 802.11 b/g/n |
| Resolution | 240×320 pixels |
| Model No. / Name | ESP32-S3 |
| SRAM | 512 KB |
| Shipping Weight | 0.065 kg |
| Shipping Dimensions | 11 × 8 × 3 cm |
Overview
The Waveshare ESP32-S3 2.8inch Capacitive Touch Display Development Board, 240×320, IPS, 5-point Touch, 32-bit LX7 Dual-core Processor, Supports WiFi & Bluetooth, ESP32 With Display, made by WAVESHARE, is listed in our iot development boards range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Interface: USB Type-C (confirm your cable or board uses the same connector)
- Controller: ESP32-S3
- Input Voltage (V): 5V (match this to your power supply; too high a voltage can damage the part)
- GPIO: Multiple General Purpose Input/Output pins
- Processor: 32-bit LX7 dual-core (look up this chip to confirm it runs the firmware or libraries you plan to use)
- Flash Memory: 16 MB (more memory leaves room for larger programs and buffers)
- WiFi (Y/N): IEEE 802.11 b/g/n (2.4 GHz reaches further, 5 GHz is faster at short range)
- Resolution: 240×320 pixels
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
Features:
- Equipped with high-performance Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
- Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
- Built-in 512KB SRAM and 384KB ROM, with onboard 16MB Flash and 8MB PSRAM
- Onboard 2.8inch capacitive touch display, 240×320 resolution, 262K color
- Supports capacitive touch control via I2C interface, 5-point touch with interrupt support
- Adapting UART, I2C and some IO interfaces, integrates full-speed USB port
- Onboard speaker, QMI8658 6-axis sensor, RTC sensor, TF card slot and battery recharge management module, etc.
- Supports accurate control such as flexible clock and multiple power modes to realize low power consumption in different scenarios
Package Includes:
- SH1.0 4PIN cable ~100mm ×1
- SH1.0 12PIN cable ~100mm ×1
- SH1.0 4PIN cable ~100mm (2pcs) ×1
- 2030 speaker ×1
Quick specs
- Interface
- USB Type-C
- Controller
- ESP32-S3
- Input Voltage (V)
- 5V
- GPIO
- Multiple General Purpose Input/Output pins
- Processor
- 32-bit LX7 dual-core
- Flash Memory
- 16 MB



















