Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by WAVESHARE, this soil moisture sensors is a good fit for makers, students and electronics hobbyists. Main specs: item type Sensor; model no. / name Moisture Sensor; dimensional accuracy (mm) 20.0mm x 51.0mm. Check that your power source supplies 2 to 5 before connecting it.

Key Highlights

  • Item Type: Sensor
  • Model No. / Name: Moisture Sensor
  • Dimensional Accuracy (mm): 20.0mm x 51.0mm

Ideal For

  • Arduino, ESP32 and Raspberry Pi projects
  • School and college lab work
  • Prototypes and test rigs

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeSensor
Model No. / NameMoisture Sensor
Rated Voltage (VDC)2 to 5
Dimensional Accuracy (mm)20.0mm x 51.0mm
Output TypeAnalog output
Mounting Hole Diameter (mm)2.0mm
Shipping Weight0.007 kg
Shipping Dimensions7 × 5 × 1 cm

Overview

The Waveshare Moisture Sensor, made by WAVESHARE, is listed in our soil moisture sensors range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: Sensor
  • Model No. / Name: Moisture Sensor
  • Rated Voltage (VDC): 2 to 5 (match this to your power supply; too high a voltage can damage the part)
  • Dimensional Accuracy (mm): 20.0mm x 51.0mm (measure your mounting space before ordering)
  • Output Type: Analog output
  • Mounting Hole Diameter (mm): 2.0mm
  • Shipping Weight: 0.007 kg (important for drones, RC models and anything you carry)
  • Shipping Dimensions: 7 × 5 × 1 cm (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

This is Waveshare Moisture Sensor. The sensor to determine the moisture level of the soil. It is powered with the voltage from 3.1 V to 5 V. The output is the analog voltage which increases its value along with the increasing moisture content which makes it compatible with most commissioning modules, for example, Arduino. The device can be used, for example, for measuring the moisture content of the soil in the pot. The sensor has an analog output that should be connected to the pin of the A/D converter (analog input in Arduino). This will allow you to measure the proportional voltage signal and at the same time to determine the level of soil moisture. Operating principle: This module is an application of the current amplification by a transistor. When the water in the soil is sufficient enough to conduct the current between the base and the positive power supply, a certain amount of current is generated between the base and the emitter. And in a mean while, an electric current is produced in a certain amplification factor between the collector and the emitter, and applied to the resistant in the emitter to produce a voltage. Then, this voltage will be collected by an AD converter.

Application:

  1. Auto watering system
  2. Flowerpot soil moisture detection
  3. Auto pouring system

Features: 

  1. Auto watering system
  2. Flowerpot soil moisture detection
  3. Auto pouring system
  4. VCC ↔ 2.0V ~ 5.0V
  5. GND ↔ power supply ground
  6. AOUT ↔ MCU.IO (analog output)

Package Includes:

1 x Moisture Sensor

1 x 3-pin custom connector jumper wire

Quick specs

Item Type
Sensor
Model No. / Name
Moisture Sensor
Rated Voltage (VDC)
2 to 5
Dimensional Accuracy (mm)
20.0mm x 51.0mm
Output Type
Analog output
Mounting Hole Diameter (mm)
2.0mm
See all specifications