
1 / 5 · Click to enlarge
AI Summary
A stackable Raspberry Pi HAT built on the SIM7600G-H module that adds LTE Cat-4 4G with 3G and 2G fallback plus GPS, BeiDou and GLONASS positioning. It also handles calls, SMS and AT commands over USB or UART.
Key Highlights
- LTE Cat-4 4G module with 3G and 2G network fallback
- GPS, BeiDou and GLONASS positioning with 16-channel receiver
- Standard 40-pin GPIO header fits Raspberry Pi series and Jetson Nano
- Onboard CP2102 USB-to-UART converter for serial debugging
- 3.5 mm headphone and mic jack for telephone calls
- Micro-SIM slot plus TF card slot for data storage
Ideal For
- Makers building remote monitoring nodes with cellular backhaul
- Raspberry Pi users adding GPS tracking to a portable project
- Developers testing AT commands and SMS workflows
- Students learning cellular and GNSS integration
- Field deployments needing internet without fixed broadband
Buying Tip
Check that the module's supported bands match the LTE and 2G/3G networks in your country before ordering, since this is a region-specific variant.
Elecvora expert review
Our verdict
A well-organised cellular and GNSS HAT that bundles the modem, level shifting, audio, SIM and storage interfaces onto one stackable board. It suits builders who want a documented starting point for connected Pi projects rather than a bare module.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Cellular data, voice, SMS and GNSS on a single HAT
- Jumper-selectable UART, power and flight mode routing
- Works with Raspberry Pi series boards and Jetson Nano
- Onboard USB-to-UART converter simplifies debugging
Cons
- Region-specific band support must be verified before purchase
- Requires a separate micro-SIM and antennas, which are not listed as included
- Antenna connectors and jumper settings add setup steps for beginners
Best for
Raspberry Pi and Jetson Nano projects that need cellular data plus location
Not ideal for
Users who want a plug-and-play USB dongle with no configuration
Specifications
| Item Type | HAT |
|---|---|
| Compatibility | Pi Series |
| HAT Type | LTE HAT |
| Frequency Band | GSM/GPRS/EDGE: 850/900/1800/1900 MHz, 2G |
| Satellite Systems Supported | GPS/Beidou/GLONASS |
| Receiver Type | 16-channel; C/A Code |
| Sensitivity (dBm) | -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BeiDou) Cold starts: -148 dBm |
| Additional Specs. | Time-To-First-Fix (open air), Cold starts: <35s Hot starts: <1s |
| SMS | Supported types: MT, MO, CB, Text, PDU Storage: USIM card and ME (default) |
| Operating Voltage (VDC) | 3.3 ~ 5 |
| Operating Temperature (°C) | -30 to 80 |
| Length (mm) | 65 |
| Width (mm) | 56 |
| Weight (g) | 25 |
| Shipping Weight | 0.23 kg |
| Shipping Dimensions | 12 × 8 × 5 cm |
Frequently Asked Questions
Which boards can I use this HAT with?
Does it need a separate SIM card?
What voltage does the board require?
Can I make phone calls and send SMS?
What positioning systems are supported?
How do I test the module before building a project?
Overview
The Waveshare SIM7600G-H 4G HAT is a communication and positioning add-on board for Raspberry Pi series boards and Jetson Nano. It combines an LTE Cat-4 cellular modem with a multi-constellation GNSS receiver, so a single HAT can handle internet access, voice, messaging and location data. The board measures 65 x 56 mm and weighs around 25 g, and it accepts a supply between 3.3 V and 5 V.
Key Features
- Cellular data: LTE Cat-4 operation with 3G and 2G fallback, covering GSM/GPRS/EDGE at 850/900/1800/1900 MHz.
- Positioning: GPS, BeiDou and GLONASS support from a 16-channel C/A code receiver.
- Voice and messaging: Telephone calls and SMS through the onboard 3.5 mm earphone and mic jack, driven by AT commands.
- Protocol support: Dial-up, TCP, UDP, DTMF, HTTP and FTP communication.
- Flexible interfacing: 40-pin GPIO header, breakout UART pins and an onboard USB interface for AT command testing and GPS data.
- Storage and SIM: Micro-SIM slot supporting 1.8 V and 3 V cards, plus a TF card slot for files and messages.
Specifications Explained
The 16-channel receiver with C/A code tracking is the core of the GNSS side. Sensitivity is rated at -159 dBm for GPS and -158 dBm for GLONASS, with cold starts at -148 dBm. Time-to-first-fix is under 35 seconds from a cold start and under 1 second from a hot start in open air, which matters when a project powers up in the field and needs a position quickly.
An onboard TXS0108EPWR voltage translator shifts 3.3 V or 5 V logic down to 1.8 V, so the HAT can sit on different host boards without level conflicts. The CP2102 USB-to-UART converter gives you a serial path for debugging or logging into the Pi, while jumper blocks let you choose how UART, power and flight mode are routed — including automatic startup on power-up or control from the Raspberry Pi D6 and D4 pins.
The operating range of -30 to 80 degrees Celsius suits outdoor enclosures and vehicle installations in most climates.
Compatibility and Requirements
The board uses a standard Raspberry Pi 40-pin GPIO extension header and supports Raspberry Pi series boards as well as Jetson Nano. Breakout UART control pins allow connection to host boards such as Arduino or STM32. You will need a micro-SIM card, an antenna connected to the MAIN, AUX or GNSS connectors as appropriate, and a suitable power source within the 3.3 to 5 V range. This is a region-specific module, so confirm the supported bands match your local networks before ordering.
Typical Uses
- Remote sensor and telemetry projects that need cellular backhaul
- Vehicle or asset tracking with GNSS positioning
- SMS-based alerts and control systems
- Portable internet access for a Raspberry Pi in the field
- Learning and prototyping with AT commands and cellular protocols



Quick specs
- Item Type
- HAT
- Compatibility
- Pi Series
- HAT Type
- LTE HAT
- Frequency Band
- GSM/GPRS/EDGE: 850/900/1800/1900 MHz, 2G
- Satellite Systems Supported
- GPS/Beidou/GLONASS
- Receiver Type
- 16-channel; C/A Code



















