Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A slim 3S protection board for 11.1V lithium packs that adds overcharge, over-discharge, over-current and short circuit cut-off. Its 50 x 16 x 2 mm size makes it easy to tuck into compact DIY battery builds.

Key Highlights

  • Three-series protection for 11.1V and 12.6V lithium packs
  • Overcharge, over-discharge, over-current and short circuit protection
  • Low quiescent current of about 30 uA
  • Compact 50 x 16 x 2 mm board weighing about 16 g shipped
  • Automatic recovery once protection conditions clear
  • Transient current handling from 9-10A to 10-13A depending on variant

Ideal For

  • DIY builders assembling 3S 18650 battery packs
  • Makers building compact 11.1V portable power units
  • RC hobbyists using protected three-cell lithium packs
  • Repairers replacing a failed 3S protection board
  • Gadget builders needing a slim in-line protection module

Buying Tip

Check that your cells are rated 3C or higher for loads above 3A, and balance all three cells to the same voltage before wiring the board.

Elecvora expert review

Our verdict

A tidy, low-cost protection module for three-cell lithium packs that covers the core safety cut-offs in a very small footprint. It suits careful DIY builders who understand cell matching and current ratings.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Very compact 50 x 16 x 2 mm board
  • Four protection functions in one module
  • Automatic recovery after faults clear
  • Low quiescent current around 30 uA

Cons

  • Current rating varies by variant, so the exact figure must be confirmed
  • Requires a 12.6V charge to activate after wiring
  • Cells must be matched and rated for the intended discharge current

Best for

DIY 3S lithium battery pack builders

Not ideal for

High-current packs beyond the stated transient rating

Specifications

Under-Voltage Protection (V)Yes
Life Cycle>30000h.
Internal Resistance (Ohm)< 100m
Supply Current6 ~ 8
Max. Transient Current (A)#1: 9-10A, #2:10-13A.
Model No. / NameHX-3S-01.
Over-voltage Range4.25-4.35v±0.05v.
Quiescent Current30 uA
Storage Temperature (°C)-40 to 80
Dimensions (L x W x H) mm50 x 16 x 2
Shipping Weight0.016 kg
Shipping Dimensions5 × 3 × 2 cm

Frequently Asked Questions

What battery configuration does this board support?
It is designed for three cells in series, covering 10.8V polymer packs, 11.1V 18650 or 3.7V lithium packs, and 12.6V full-charge lithium configurations.
What protections does it provide?
The board offers overcharge, over-discharge, over-current and short circuit protection, and it cancels protection automatically once conditions return to normal.
Why is there no output after wiring?
The board needs a charge at 12.6V to activate after connection. Apply the charge first, then output should become available.
What discharge rate do my cells need?
For loads above 3A, use cells rated 3C or higher. A 2000mAh 3C cell supports about 6A, while a 2000mAh 1C cell supports about 2A.
Can I mix cells at different voltages?
No. Bring every cell to the same voltage before assembly, otherwise the pack will perform unevenly and may be damaged.
What are the physical dimensions?
The board measures 50 x 16 x 2 mm and ships at about 0.016 kg with shipping dimensions of 5 x 3 x 2 cm.

Overview

The HX-3S-01 is a small battery protection board built for three-cell lithium packs. It connects in line with a 3S 18650 or lithium polymer assembly and monitors the pack for unsafe conditions. When overcharge, over-discharge, over-current or short circuit events occur, the board interrupts the circuit. Once conditions return to normal, protection is cancelled automatically so the pack can be used again.

At 50 x 16 x 2 mm, the board fits into tight enclosures and shrink-wrapped packs. Its low quiescent current of roughly 30 uA keeps standby drain modest, and the stated life cycle exceeds 30000 hours.

Key Features

  • Three-series design: intended for 3S packs, including 11.1V rated 18650 packs and 12.6V full-charge configurations.
  • Four protection functions: overcharge, over-discharge, over-current and short circuit protection in one module.
  • Automatic recovery: protection is released when the triggering condition is removed.
  • Low standby draw: quiescent current around 30 uA.
  • Compact format: 50 x 16 x 2 mm with a shipping weight of about 0.016 kg.

Specifications Explained

Over-voltage range: the board trips at roughly 4.25-4.35V per cell with ±0.05V tolerance, helping prevent a cell from being pushed too high during charging.

Max transient current: listed as 9-10A for one variant and 10-13A for another, so check which version you receive before matching it to your load.

Internal resistance: under 100 milliohms, keeping losses low in normal use.

Supply current: stated as 6 to 8, so confirm the exact figure for your build before relying on it for continuous draw.

Storage temperature: rated from -40 to 80 degrees Celsius for storage.

Compatibility and Requirements

Use only with three-cell lithium packs. The board is intended for 10.8V rated polymer packs, 11.1V rated 18650 or 3.7V lithium packs, and 12.6V full-charge lithium configurations. Cells in series should be at the same voltage before assembly; balance or fully charge each set first if they differ. After wiring, the pack needs a charge at 12.6V to activate and produce output. For discharge currents above 3A, the pack should be rated 3C or higher: a 2000mAh 1C cell supports about 2A, while a 2000mAh 3C cell supports about 6A.

Typical Uses

Suitable for DIY 3S 18650 battery packs, small portable power builds, protected 11.1V and 12.6V battery assemblies, and compact RC or gadget projects that use a three-cell lithium pack and need basic electronic protection.

What's in the Box

Package contents are not specified for this listing. Confirm the included items with the seller before ordering.

Quick specs

Under-Voltage Protection (V)
Yes
Life Cycle
>30000h.
Internal Resistance (Ohm)
< 100m
Supply Current
6 ~ 8
Max. Transient Current (A)
#1: 9-10A, #2:10-13A.
Model No. / Name
HX-3S-01.
See all specifications