Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A small LED board that shows the charge level of a 3S 18650 lithium pack in four steps from 25 to 100 percent. Press the trigger switch for a three-second readout, then it powers down on its own.

Key Highlights

  • Four green LEDs indicate 25, 50, 75 and 100 percent charge levels
  • Designed for 3S lithium packs across a 9 to 12.6V range
  • Push-button trigger shows the level, then auto power-off after 3 seconds
  • Low static current draw of 2 to 3 mA
  • Compact 50 x 10 mm board weighing about 15 g
  • Simple two-wire style installation for DIY battery builds

Ideal For

  • RC car and boat hobbyists running 3S lithium packs
  • FPV builders assembling custom 3S battery setups
  • Robotics and DIY electronics makers
  • Students learning about lithium battery monitoring
  • Makers adding a simple level check to project enclosures

Buying Tip

Confirm your pack is a 3S lithium configuration within 9 to 12.6V before ordering, and check the 1S, 2S or 4S variants if your cell count differs.

Elecvora expert review

Our verdict

A practical, low-cost way to add a push-button charge check to a 3S lithium build without wiring in a full voltmeter. The four-step readout is coarse, but for a quick pre-run glance it does the job and stays out of the way the rest of the time.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Very small and light, so it fits tight builds
  • Auto power-off keeps display time short
  • Low 2 to 3 mA static draw
  • Simple four-LED readout is easy to interpret

Cons

  • Readout is coarse, with only four levels
  • Not a substitute for a precise voltage meter
  • Wiring and mounting hardware are not included

Best for

Hobbyists who want a fast, simple charge check on a 3S lithium pack

Not ideal for

Anyone needing precise voltage readings or continuous monitoring

Specifications

Item TypeBattery Testing Equipment
Model No. / NameBattery Level Indicator/Monitor
Voltage Rating (V)9 to 12.6
CompatibilityLithium Battery
Additional Specs.Static Current Consumption: 2~3 mA
Length (mm)50
Width (mm)10
Weight (g)15
ColorBlue
Shipping Weight0.02 kg
Shipping Dimensions5 × 1 × 1 cm

What's in the box

  • 1 x 3S 18650 Lithium Battery Capacity Indicator Module Level Tester LED

Frequently Asked Questions

What battery type does this module work with?
It is designed for 3S lithium battery packs within a 9 to 12.6V range. It is not intended for other chemistries or cell counts.
How do I read the charge level?
Press the trigger switch and count the lit green LEDs. The first light indicates roughly 25 percent, the second 50 percent, the third 75 percent and the fourth 100 percent.
Does the display stay on?
No. The board powers off automatically after about three seconds, so you press the switch each time you want a reading.
How much current does it draw when idle?
Static current consumption is listed at 2 to 3 mA, which is low enough to be negligible in most builds.
What is included in the package?
The package contains 1 x 3S 18650 Lithium Battery Capacity Indicator Module Level Tester LED. Wiring and mounting hardware are not listed.
Are other cell counts available?
Yes, this indicator is offered in 1S, 2S, 3S and 4S variants. Choose the one that matches your battery configuration.

Overview

The Generic 3S 18650 Lithium Battery Capacity Indicator Module is a small display board that turns a battery check into a single button press. Instead of reaching for a multimeter, you tap the trigger switch and read the charge level from four green LEDs. The board is built for 3S lithium packs and works across a 9 to 12.6V range, which covers the usual span between a discharged and fully charged 3S pack.

Because the readout only lasts about three seconds, the module is not a permanent gauge you monitor constantly. It is a check-on-demand tool: press, read, and let it shut down. That behaviour, plus a static current consumption of just 2 to 3 mA, keeps its impact on the pack minimal.

Key Features

  • Four-step LED readout: each lit LED corresponds to a higher charge band, from the first light at roughly 25 percent up to the fourth at full charge.
  • Trigger switch operation: a light push activates the display, and the board powers off automatically after about three seconds.
  • 3S voltage range: rated for 9 to 12.6V, matching the expected operating window of a three-cell lithium series pack.
  • Low standby draw: static current consumption is listed at 2 to 3 mA.
  • Compact footprint: 50 mm long, 10 mm wide and around 15 g, so it tucks into tight builds.
  • Green LED indication: clear, easy-to-read lights in a blue board finish.

Specifications Explained

Voltage rating 9 to 12.6V: this is the working range for a 3S lithium configuration. The top of the range, 12.6V, is the typical full-charge point for three cells in series, while the lower end reflects a pack that is running down. Using the module outside this range is not what it is designed for.

LED thresholds: the display steps through four levels. The first light comes on around 3.1V, the second around 6.3V, the third around 9.4V and the fourth around 12.6V, giving you a coarse but quick sense of where the pack sits.

Static current 2 to 3 mA: this is the small amount the board consumes when idle. It is low enough to be negligible in most hobby builds, but it is still worth planning how the module is connected if the pack will sit unused for long periods.

Size and weight: at 50 x 10 mm and about 15 g, the board adds very little bulk. Shipping weight is listed at 0.02 kg with shipping dimensions of 5 x 1 x 1 cm.

Compatibility and Requirements

This module is intended for lithium batteries in a 3S configuration within the stated 9 to 12.6V rating. It is not a universal voltage meter and should not be treated as one. Wiring and mounting hardware are not listed in the package contents, so plan for your own connections and enclosure arrangement. If you are working with a different cell count, check the available 1S, 2S and 4S variants of this indicator instead.

Typical Uses

  • Checking charge level on custom 3S 18650 packs before a run
  • Adding a simple level readout to RC cars, boats and aircraft
  • Battery monitoring in robotics and DIY electronics projects
  • Quick field checks on FPV ground station or accessory packs
  • Teaching builds where a clear visual voltage indicator helps

What's in the Box

1 x 3S 18650 Lithium Battery Capacity Indicator Module Level Tester LED.

Quick specs

Item Type
Battery Testing Equipment
Model No. / Name
Battery Level Indicator/Monitor
Voltage Rating (V)
9 to 12.6
Compatibility
Lithium Battery
Additional Specs.
Static Current Consumption: 2~3 mA
Length (mm)
50
See all specifications