Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The BIGTREETECH BTT Manta M8P is a 32-bit control board with eight driver slots and BTB core board support. Its TPS5450-5A power chip and jumper-selectable PT1000 support make it a flexible foundation for custom 3D printer builds.

Key Highlights

  • 32-bit STM32G0B1VET6 microcontroller at 64 MHz
  • Eight driver slots with onboard SPI and UART modes
  • BTB connection supports CM4 or BIGTREETECH CB1 core boards
  • TPS5450-5A power chip for Raspberry Pi power supply
  • Jumper-selectable thermistor pull-up for PT1000 sensors
  • Reserved SPI interface for Klipper acceleration sensors

Ideal For

  • 3D printer builders designing custom CoreXY or Cartesian machines
  • Users upgrading from 8-bit boards to 32-bit with Klipper
  • Makers who want to run a Raspberry Pi CM4 or BTT CB1 as the host
  • Enthusiasts planning multi-extruder or heated chamber setups
  • DIYers who need PT1000 support without extra modules

Buying Tip

Confirm that you have a compatible core board (CM4 or CB1) and a suitable 12V or 24V power supply before ordering, as neither is included.

Elecvora expert review

Our verdict

The BIGTREETECH Manta M8P is a well-equipped 32-bit board that offers excellent flexibility for custom 3D printer builds, especially for Klipper users. Its BTB core board design and extensive I/O make it a strong foundation for advanced setups, though it requires additional components to operate.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Eight driver slots with SPI/UART modes for TMC drivers
  • BTB connection supports CM4 and CB1 core boards
  • TPS5450-5A power chip can supply a Raspberry Pi
  • Jumper-selectable PT1000 support without extra modules
  • Reserved SPI interface for Klipper acceleration sensors

Cons

  • Core board (CM4 or CB1) is not included and must be purchased separately
  • Requires a separate 12V or 24V power supply
  • No onboard drivers; stepper drivers must be added

Best for

Advanced 3D printer builders using Klipper who want a flexible, expandable control board.

Not ideal for

Beginners looking for a plug-and-play board with included drivers and power supply.

Specifications

Item TypeController Board
CompatibilityGeneral Purpose
Input Voltage (VDC)VIN=DC12V or DC24V
MicrocontrollerSTM32G0B1VET6
Frequency64 MHz
Driver Slot8
Heating interfacehot bed (HB), heating rod (HE0, HE1, HE2, HE3)
Fan Port2 pins PWM Fan x 5 4pins PWM Fan x 2 Always on Fan x 1 SoC Fan x 1
Fan Voltage Selection (Y/N)Y, (24V, 12V, 5V)
Length (mm)170
Width (mm)102
Weight (g)186
Shipping Weight0.318 kg
Shipping Dimensions21 × 14 × 5 cm

What's in the box

  • 1 x BIGTREETECH Manta M8P Control Board
  • 1 x Type C USB Cable
  • 1 x DIY Crimp Terminal Set
  • 1 x Black jumper set

Frequently Asked Questions

What core boards are compatible with the Manta M8P?
The board uses a BTB connection that supports Raspberry Pi CM4 and BIGTREETECH CB1 core boards. Other core board solutions may also be compatible if they use the same interface.
Can I use a PT1000 sensor without an external module?
Yes, the thermistor pull-up resistance can be selected via a jumper, allowing direct connection of PT1000 sensors without additional modules.
What input voltage does the board require?
The board accepts DC12V or DC24V input via the VIN terminal. Ensure your power supply can provide sufficient current for your heaters and peripherals.
Does the package include stepper drivers?
No, stepper drivers are not included. The board has eight driver slots and supports TMC drivers in SPI and UART modes.
How can I update the firmware?
Firmware can be updated via an SD card or through Klipper’s make flash command using DFU.
What fan voltages are supported?
Fan voltage can be selected between 24V, 12V, and 5V using jumpers, covering a range of fan types.

Overview

The BIGTREETECH BTT Manta M8P is a 32-bit control board designed for custom 3D printer builds and upgrades. It uses the STM32G0B1VET6 microcontroller running at 64 MHz and provides eight driver slots, giving you room to configure multiple stepper motors for complex kinematics. The board accepts DC12V or DC24V input and uses a TPS5450-5A power chip that can deliver up to 5A, sufficient for powering a Raspberry Pi alongside the printer electronics.

What sets the Manta M8P apart is its BTB connection between the control board and the core board. This design allows you to use a Raspberry Pi CM4 or a BIGTREETECH CB1, so you are not locked into a single compute module. The board also includes a reserved SPI expansion interface for connecting an external acceleration sensor when running Klipper firmware, enabling input shaping and acceleration compensation.

Key Features

  • STM32G0B1VET6 microcontroller: 32-bit ARM Cortex-M0+ core at 64 MHz for responsive control.
  • Eight driver slots: Onboard TMC-driver SPI and UART working modes with DIAG function pins, configurable via jumpers.
  • BTB core board connection: Supports Raspberry Pi CM4 and BIGTREETECH CB1 for flexible compute options.
  • Powerful 5A supply: TPS5450-5A chip with 5A output (6A peak) to power a Raspberry Pi reliably.
  • PT1000 ready: Jumper-selectable thermistor pull-up resistance supports PT1000 sensors without external modules.
  • Fan and heating outputs: Hot bed (HB) and four heating rod interfaces (HE0–HE3); five 2-pin PWM fans, two 4-pin PWM fans, one always-on fan, and one SoC fan, with selectable 24V, 12V, or 5V fan voltage.
  • Expandable: Reserved three-way four-wire fan interface for water-cooling devices and SPI expansion for Klipper sensors.
  • Serviceable design: High-efficiency MOSFETs reduce heat, and a replaceable fuse simplifies maintenance.

Specifications Explained

Microcontroller and frequency: The STM32G0B1VET6 at 64 MHz provides enough processing headroom for typical 3D printing tasks, including multiple axes and temperature control.

Driver slots: Eight slots let you install stepper drivers for multi-axis setups. Onboard SPI and UART modes mean you can use TMC drivers with advanced features, and DIAG pins are accessible via jumpers for sensorless homing or stall detection.

Power input and supply: VIN accepts DC12V or DC24V. The TPS5450-5A power chip delivers up to 5A (6A peak), which is enough to power a Raspberry Pi directly from the board, reducing wiring complexity.

Heating and fan interfaces: The board includes a hot bed output and four heating rod outputs (HE0–HE3), plus a mix of PWM and always-on fan ports. Fan voltage can be selected between 24V, 12V, and 5V via jumpers, so you can match your fans without extra converters.

Thermistor support: A jumper lets you select the pull-up resistance value, enabling direct connection of PT1000 sensors without external amplifier modules.

Dimensions: 170 mm × 102 mm, weight 186 g, compact enough for most printer frames.

Compatibility and Requirements

The Manta M8P is designed for general-purpose 3D printer control. It requires a compatible core board (Raspberry Pi CM4 or BIGTREETECH CB1) to operate, which is not included. Firmware can be updated via SD card or through Klipper’s make flash command using DFU. The board supports filament runout detection, auto shutdown, BLTouch, and RGB lights when connected. A separate power supply (DC12V or DC24V) is required and not included. The package includes a Type-C USB cable, DIY crimp terminal set, and black jumper set for setup.

Typical Uses

This control board is suitable for custom Cartesian, CoreXY, and delta 3D printers, as well as upgrades of older 8-bit boards. It is particularly useful for users who want to run Klipper with input shaping, thanks to the SPI expansion for an accelerometer. The multiple fan and heating outputs support heated chambers, water cooling, and multi-extruder setups. The BTB core board design makes it a good choice for those who prefer a compact electronics enclosure with a Raspberry Pi integrated.

What's in the Box

  • 1 × BIGTREETECH Manta M8P Control Board
  • 1 × Type-C USB Cable
  • 1 × DIY Crimp Terminal Set
  • 1 × Black Jumper Set

Quick specs

Item Type
Controller Board
Compatibility
General Purpose
Input Voltage (VDC)
VIN=DC12V or DC24V
Microcontroller
STM32G0B1VET6
Frequency
64 MHz
Driver Slot
8
See all specifications