Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by BIGTREETECH, this 3d printer display and controller is a good fit for 3D printing users. Main specs: item type Controller Board; compatibility General Purpose; input voltage (vdc) 12–24. Check that your power source supplies 12–24 before connecting it.

Key Highlights

  • Item Type: Controller Board
  • Compatibility: General Purpose
  • Input Voltage (VDC): 12–24

Ideal For

  • Upgrading or repairing a 3D printer
  • Spare parts for long prints
  • Testing new materials

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeController Board
CompatibilityGeneral Purpose
Input Voltage (VDC)12–24
Flash1MB
MicrocontrollerSTM32H723ZET6
Batteries RequiredNo
Communication InterfaceUSB Type-C
Controllable Fans6 controllable fans, two normally open fans, and both support power supply voltage, 12V, 5V options.
Length (mm)160
Width (mm)100
Weight (g)195
Shipping Weight0.33 kg
Shipping Dimensions19 × 13 × 4.5 cm

Overview

The BIGTREETECH BTT Octopus Pro V1.0.1 (H723) 3D Printer Controller Board, made by BIGTREETECH, is listed in our 3d printer display and controller range and suits 3D printing users. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: Controller Board
  • Compatibility: General Purpose
  • Input Voltage (VDC): 12–24 (match this to your power supply; too high a voltage can damage the part)
  • Flash: 1MB (space for firmware, files or media)
  • Microcontroller: STM32H723ZET6 (look up this chip to confirm it runs the firmware or libraries you plan to use)
  • Batteries Required: No
  • Communication Interface: USB Type-C (confirm your cable or board uses the same connector)
  • Controllable Fans: 6 controllable fans, two normally open fans, and both support power supply voltage, 12V, 5V options. (match this to your power supply; too high a voltage can damage the part)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

This is BIGTREETECH BTT Octopus Pro V1.0.1 (H723) 3D Printer Controller Board.

BIGTREETECH Octopus Pro V1.0.1(H723) board adopts the ARM Cortex-M7 series, STM32H723ZET6, main frequency up to 550MHz, Processing is more stable and fast. Supports Marlin and klipper, the best choice for Klipper high-speed printing meet the individual need of DIY users, support Operation systems Raspberry Pi / Octoprint. Support 8 axis powerful motor driver ,support 5V level for stepper motor driver ,better performance. support max 60V motor input voltage to improve motor power ,reduce pulse losing. Support STEP/DIR/UART/SPI Mode.

Octopus Pro (H723) has a unique feature with its STM32H723ZET6 chip pins. When the chip enters DFU mode, the HE0 and HE2 will immediately start working. To prevent any damage or safety hazards resulting from prolonged heating of the heater cartridge, it is highly recommended not to enter DFU mode while the motherboard is powered by a 12/24V power supply. Following are the characteristics of BIGTREETECH Octopus Pro V1.0.1 (H723).

  1. Main Control Chip: The main control board uses 32-bit ARM-level Cortex-M4 STM32H723ZE and the flash is 1MB.
  2. Support 60V Input: Supports up to 8 3D printer motherboards with a maximum 60V stepper motor. The motor drive power supply supports up to 60V input (only for the motor drive power supply).
  3. 6 Controllable Fans: Up to 6 controllable fans, two normally open fans, and both support power supply voltage, 12V, 5V options.
  4. Update Firmware: Klipper/Marlin/RRFSupports firmware update via DFU mode. This is where the firmware is sent to the board directly from the PC and does not require a bootloader however this method is not recommended for novice users as discussed later in this document.
  5. Level conversion IC: Supports proximity sensor, jumper optional pull-up resistor, supports more models, supports BL Touch.


Features:

  1. Designed for 8 powerful stepper drivers
  2. 169 Mhz or 180 Mhz ARM Cortex-M4 CPU
  3. MAX31865 chip for HT thermistors
  4. Max. 60 volt voltage, optionally adjustable

Package Includes:

1 x BIGTREETECH Octopus Pro V1.0.1(H723)

1 x Accessories Set (as shown in image)

Quick specs

Item Type
Controller Board
Compatibility
General Purpose
Input Voltage (VDC)
12–24
Flash
1MB
Microcontroller
STM32H723ZET6
Batteries Required
No
See all specifications