Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact digital LDR light sensor module that outputs a simple high or low signal depending on ambient light. The onboard potentiometer lets you set the light threshold yourself, making it easy to trigger Arduino inputs or relay modules.

Key Highlights

  • LM393-based digital light detection with adjustable trigger threshold
  • Runs from 3.3V to 5V DC and draws about 15mA
  • Digital DO output delivers a clean high or low TTL signal
  • Onboard power LED and status LED for quick visual checks
  • Compact 36 x 14mm board with an M3 mounting hole
  • Lightweight at roughly 3g for easy placement

Ideal For

  • Arduino beginners learning digital sensor inputs
  • Makers building automatic or light-triggered lamps
  • Students working on photoelectric switch projects
  • Hobbyists adding ambient light sensing to enclosures
  • Developers prototyping relay-controlled lighting logic

Buying Tip

Before mounting the board, power it up and turn the potentiometer while watching the status LED so you know exactly where your light threshold sits.

Elecvora expert review

Our verdict

A straightforward, low-cost way to add digital light detection to a project without writing threshold code. The adjustable potentiometer and dual LEDs make setup quick, though the output is binary rather than a measured light value.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Simple high or low output needs no analog reading
  • Adjustable threshold via onboard potentiometer
  • Works on both 3.3V and 5V supplies
  • Power and status LEDs speed up setup
  • Compact board with an M3 mounting hole

Cons

  • Gives only a digital state, not a light intensity value
  • Jumper wires and a power source are not included
  • Threshold may need retuning if lighting conditions change

Best for

Arduino users who need a simple light-triggered digital signal

Not ideal for

Projects that require precise lux or analog light measurements

Specifications

Model No. / NameLight Dependent Resistor Module
Operating Voltage (V)3.3 to 5
Operating Current (mA)15
Length (mm)36
Width (mm)14
Weight (g)3
Shipping Weight0.005 kg
Shipping Dimensions4 × 3 × 2 cm

What's in the box

  • 1 x Digital LDR Light Sensor Module

Frequently Asked Questions

What does the DO pin output?
It provides a digital high or low signal based on whether ambient light is above or below the threshold you set. Connect it to a digital input on your microcontroller.
Can I use this module with a 3.3V board?
Yes. The module accepts 3.3V to 5V DC, so it suits both 3.3V and 5V logic systems when wired to a matching supply.
How do I change the light sensitivity?
Turn the onboard blue potentiometer while watching the status LED. Stop when the LED switches at the light level you want to detect.
Can it drive a relay directly?
The digital output can be connected to a relay module to form a photoelectric switch. Use a relay module suited to your load and supply.
What is included with the module?
The package contains one LDR module. Jumper wires, a power supply and mounting hardware are not included.
How much current does it draw?
The module draws approximately 15mA at its operating voltage, which is low enough for most small projects.

Overview

This digital LDR light sensor module is a small, self-contained board that answers one simple question for your project: is the ambient light brighter or dimmer than the level I set? A Light Dependent Resistor changes resistance with light, and an LM393 comparator turns that change into a clean digital signal on the DO pin. Instead of reading an analog value and writing your own threshold logic, you get a ready-made high or low output you can feed straight into a microcontroller input.

The threshold is set with the onboard blue potentiometer, so you can tune the module to your room, enclosure or lighting conditions. Two LEDs help during setup: one shows the board has power, the other reflects the output state. The board measures 36mm by 14mm and weighs about 3g, and an M3 mounting hole makes it easy to fix to a bracket, case or chassis.

Key Features

  • LM393 comparator design for stable digital light detection
  • Adjustable sensitivity via the onboard potentiometer
  • Digital output on the DO pin, high or low depending on light level
  • Wide supply range of 3.3V to 5V DC
  • Power and status LEDs for quick visual confirmation
  • M3 mounting hole and compact 36 x 14mm footprint

Specifications Explained

Operating voltage: 3.3V to 5V

The module works with both 3.3V and 5V logic systems, which covers most common Arduino boards and many other microcontroller platforms. Match the supply to your board's logic level so the DO signal is read correctly.

Operating current: 15mA

At around 15mA, the module draws very little, so it can share a supply with other small sensors without placing a noticeable load on your regulator.

Digital output (DO)

The DO pin gives a simple high or low signal. According to the module's logic, the output goes high when light exceeds your set threshold and low when it falls below it. Check the behaviour in your own setup before relying on it.

Potentiometer

The blue trimmer sets the trigger level. Turn it while watching the status LED to find the switching point you want, then leave it fixed.

Size and weight

At 36mm long, 14mm wide and about 3g, the board fits into tight enclosures and adds almost no weight to a build.

Compatibility and Requirements

The module needs a 3.3V to 5V DC supply connected to VCC and a common ground on GND. The DO pin connects to a digital input on your microcontroller. Because the output is digital, no analog pin or analog-to-digital conversion is needed. You will need your own jumper wires and a suitable supply; these are not included.

Typical Uses

  • Detecting day versus night for automatic lighting logic
  • Monitoring ambient brightness inside a room or enclosure
  • Triggering a relay module to build a simple photoelectric switch
  • Adding light-aware behaviour to Arduino learning projects
  • Watching light levels in small automated or robotic builds

What's in the Box

One Digital LDR Light Sensor Module.

Quick specs

Model No. / Name
Light Dependent Resistor Module
Operating Voltage (V)
3.3 to 5
Operating Current (mA)
15
Length (mm)
36
Width (mm)
14
Weight (g)
3
See all specifications