
1 / 5 · Click to enlarge
AI Summary
The LAMBDOID RP-SMA male to SMA female adapter connects reverse-polarity SMA equipment to standard SMA cables and devices. Its Teflon insulator and low-loss contacts make it a dependable choice for WiFi and RF interconnects.
Key Highlights
- RP-SMA male to SMA female gender conversion
- Teflon insulator for stable RF performance
- VSWR below 1.5 for efficient signal transfer
- Handles up to 10 W RF power
- Low contact resistance: 6 mΩ centre, 2 mΩ outer
- Operates from -30°C to 60°C at 5-95% humidity
Ideal For
- WiFi and WLAN installers working with mixed RP-SMA and SMA hardware
- RF technicians building test leads and bench setups
- FPV and RC hobbyists adapting antennas and video transmitters
- Electronics hobbyists prototyping wireless projects
- IT professionals maintaining access points and antenna systems
Buying Tip
Confirm the gender of both your device port and your cable before ordering: RP-SMA male has a female socket, while SMA female has a centre pin.
Elecvora expert review
Our verdict
The LAMBDOID RP-SMA male to SMA female adapter is a well-specified small part that does a specific job reliably. Its Teflon insulator and low contact resistance make it a solid choice for WiFi and RF interconnects where signal integrity matters.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Low VSWR and contact resistance support clean RF performance
- Teflon insulator and silicone gasket add durability
- Handles 10 W, covering most low-power wireless needs
- Wide operating temperature and humidity range
Cons
- Not suitable for high-power RF systems above 10 W
- Package contents are not specified, so check what is included
Best for
WiFi and WLAN technicians adapting RP-SMA equipment to SMA cables
Not ideal for
High-power RF transmitters or outdoor long-term exposure without additional protection
Specifications
| Manufacturer | LAMBDOID |
|---|---|
| Dielectric Withstanding (V) | 500-1000 VRMS (depends on cable) |
| VSWR | < 1.5 |
| Contact Resistance (ohm) | Centre: 6 milliohm Outer: 2 milliohm |
| Power Handling (W) | 10 |
| Insulator Resistance | 500 Megaohms |
| Gender | Female, Male |
| Insulators | Teflon |
| Additional Specs. | Crimp Ferules: Annealed copper Ni/ Au plated |
| Clamp Gaskets | Silicone rubber |
| Operating Temperature (°C) | -30° to 60°C |
| Humidity Range | 5 – 95% |
| Shipping Weight | 0.001 kg |
| Shipping Dimensions | 1 × 1 × 1 cm |
Frequently Asked Questions
What is the difference between RP-SMA and SMA?
Can I use this adapter for WiFi antennas?
What is the maximum power rating?
Does this adapter change the signal frequency?
What is included in the package?
How should I care for the adapter?
Overview
The LAMBDOID RP-SMA male to SMA female adapter is a compact RF interconnect that lets you join a reverse-polarity SMA (RP-SMA) male interface to a standard SMA female connector. Reverse-polarity SMA is common in WiFi and WLAN hardware, where the mating interface is inverted compared with standard SMA. This adapter removes the guesswork from mixing the two standards, giving technicians and hobbyists a clean, secure transition without re-terminating cables.
Built with a Teflon insulator and plated annealed-copper crimp ferrules, the adapter is designed for repeatable RF connections. A silicone rubber clamp gasket helps maintain a stable fit in demanding environments.
Key Features
- Dual-interface adapter: RP-SMA male on one side, SMA female on the other.
- Teflon dielectric: provides consistent electrical insulation for RF signals.
- Low VSWR: below 1.5 for reduced signal reflection.
- 10 W power handling: suitable for typical low-power RF and WiFi applications.
- Low contact resistance: 6 milliohms at the centre and 2 milliohms at the outer conductor.
- Wide environmental range: -30°C to 60°C and 5-95% humidity.
Specifications Explained
VSWR below 1.5 means the adapter introduces minimal signal reflection, which helps preserve link quality in WiFi and other RF systems. Power handling of 10 W covers the needs of most access points, adapters and low-power transmitters. Contact resistance of 6 milliohms (centre) and 2 milliohms (outer) keeps losses low at the connection point. The Teflon insulator supports stable performance across the rated temperature range, while the silicone rubber clamp gasket helps the adapter stay firmly seated. Dielectric withstanding voltage is 500-1000 VRMS depending on the cable used.
Compatibility and Requirements
This adapter is intended for RP-SMA male to SMA female connections. It does not convert signal type or frequency; it simply provides a mechanical and electrical interface between the two connector standards. Ensure that the mating connectors on your equipment match RP-SMA male and SMA female respectively. No additional tools are required beyond those needed to mate the connectors.
Typical Uses
- Connecting RP-SMA WiFi antennas to SMA-equipped radios or test equipment.
- Adapting RP-SMA access points to standard SMA coaxial cables.
- Bench testing and prototyping where mixed SMA standards are present.
- RF interconnects in WLAN and other low-power wireless systems.
What's in the Box
Package contents are not specified by the manufacturer. Please check the product listing for details.
Quick specs
- Manufacturer
- LAMBDOID
- Dielectric Withstanding (V)
- 500-1000 VRMS (depends on cable)
- VSWR
- < 1.5
- Contact Resistance (ohm)
- Centre: 6 milliohm Outer: 2 milliohm
- Power Handling (W)
- 10
- Insulator Resistance
- 500 Megaohms


















