
1 / 3 · Click to enlarge
AI Summary
The LEGACT RP-C5-LT is a 0.25mm thin force sensitive resistor that varies resistance from 20g to 1kg. Its compact size and ±5% repeatability make it easy to integrate into Arduino, robotics, and pressure-sensing projects.
Key Highlights
- Senses applied force from 20g up to 1kg
- Ultra-thin 0.25mm profile fits tight spaces
- Repeatability of ±5% on the same part at 500g
- Non-actuated resistance above 10MΩ for clean off-state
- Operates reliably from -40°C to +85°C
- Simple two-terminal resistor interface for microcontrollers
Ideal For
- Arduino and Raspberry Pi enthusiasts building interactive sensors
- Robotics hobbyists needing grip force feedback
- Product designers prototyping touch-sensitive interfaces
- STEM educators demonstrating resistive sensing principles
- Makers creating custom input devices or wearables
Buying Tip
Remember that this is a resistive sensor, not a load cell: pair it with a fixed resistor in a voltage divider and calibrate your threshold in software for your specific force range.
Elecvora expert review
Our verdict
The LEGACT RP-C5-LT is a practical, low-cost force sensing solution for hobbyist and educational projects. Its thin profile and wide resistance range make it easy to integrate, though it is best suited to relative force detection rather than precise measurement.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Very thin and flexible for tight installations
- Wide 20g to 1kg range covers many touch applications
- Simple two-wire resistive interface
- Stable performance across a broad temperature range
Cons
- Requires an external resistor for voltage divider
- Not a precision load cell; absolute accuracy is limited
- No datasheet included in the box (available separately)
Best for
Makers and educators needing a simple force trigger
Not ideal for
Applications requiring calibrated, high-accuracy force measurement
Specifications
| Sensitivity range | 20g to 1kg |
|---|---|
| Thickness (mm) | 0.25 |
| Actuation force | 20g Res.<=200KΩ |
| Repeatability Same part | +/-5%, Ave. R@500g |
| Non-actuated resistance | >10MΩ |
| Operating Temperature (°C) | -40℃~+85℃ |
What's in the box
- 1 x Force Sensitive Resistor RP-C5-LT (20g-1kg)
Frequently Asked Questions
How do I connect the RP-C5-LT to an Arduino?
Does the sensor output a voltage directly?
What is the maximum force the sensor can handle?
Is the sensor waterproof or weatherproof?
What is included in the package?
Can I cut or trim the sensor to fit my project?
Overview
The LEGACT RP-C5-LT is a force sensitive resistor (FSR) that provides a variable resistance output based on the force applied to its sensing area. With a sensitivity range of 20g to 1kg, it is well suited to detecting presses, grips, and light impacts in embedded electronics projects. The sensor is only 0.25mm thick, so it can be placed under keypads, inside robotic fingertips, or between surfaces without adding noticeable bulk.
This FSR is a passive two-terminal device: as force increases, resistance decreases. When no force is applied, resistance stays above 10MΩ, effectively acting as an open circuit. That makes it easy to read with a microcontroller's analog input using a simple voltage divider.
Key Features
- 20g to 1kg sensing range – covers light touches through to firm presses.
- 0.25mm thickness – low-profile enough for stacked or curved installations.
- ±5% repeatability at 500g – consistent readings on the same part for reliable triggering.
- >10MΩ non-actuated resistance – minimal current draw when idle.
- -40°C to +85°C operating temperature – stable performance across demanding environments.
Specifications Explained
The sensitivity range tells you the force band where the sensor produces a useful change in resistance. Below 20g the output may be hard to distinguish; above 1kg the response saturates. The actuation force figure of 20g with resistance ≤200KΩ indicates the approximate resistance at the low end of the range, helping you set threshold values in firmware.
Repeatability of ±5% means that for repeated applications of 500g on the same sensor, you can expect readings within a narrow band. This is important for applications that rely on consistent triggering rather than absolute force measurement. The non-actuated resistance above 10MΩ ensures the sensor behaves like an open switch when untouched, simplifying detection of press versus no-press events.
Compatibility and Requirements
The RP-C5-LT is a passive resistive component and does not require a dedicated driver. It can be connected directly to any microcontroller or ADC that supports a voltage divider circuit. No specific voltage rating is stated in the product data; typical use involves a low-voltage DC supply compatible with your board. Ensure your reading circuit accounts for the sensor's resistance range (from >10MΩ down to hundreds of kilohms at 20g).
Typical Uses
- Touch and pressure sensing in Arduino or Raspberry Pi projects
- Robotic gripper feedback and end-effector force detection
- Interactive exhibits and musical interfaces
- Weight-triggered switches and presence detection
- Wearable prototypes and ergonomic input devices
What's in the Box
1 x Force Sensitive Resistor RP-C5-LT (20g-1kg)
Quick specs
- Sensitivity range
- 20g to 1kg
- Thickness (mm)
- 0.25
- Actuation force
- 20g Res.<=200KΩ
- Repeatability Same part
- +/-5%, Ave. R@500g
- Non-actuated resistance
- >10MΩ
- Operating Temperature (°C)
- -40℃~+85℃



















