Skip to main content

Worldwide Shipping · Secure Payments

At a glance

This switching ic is a good fit for everyday home and hobby use. Main specs: manufacturer Generic; min supply voltage 3.6; max. supply voltage (v) 5.5. Check that your power source supplies 3.6 before connecting it.

Key Highlights

  • Manufacturer: Generic
  • Min Supply Voltage: 3.6
  • Max. Supply Voltage (V): 5.5

Ideal For

  • Everyday use

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

ManufacturerGeneric
Min Supply Voltage3.6
Max. Supply Voltage (V)5.5
Max. Operating Current (A)10
Product TypeUSB Bridge Controllers
Processor SeriesPL2303HX
Max. Clock Frequency (MHz)12.024
Interface TypeUART
Operating Temperature (°C)-40 to 85
Mounting TypeSMD/SMT
No. of I/O pins2
Shipping Weight0.001 kg
Shipping Dimensions1 × 1 × 1 cm

Overview

The PL2303HX SSOP28 USB-to-Serial Bridge Controller IC (Revision A) is listed in our switching ic range and suits everyday home and hobby use. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Manufacturer: Generic
  • Min Supply Voltage: 3.6 (match this to your power supply; too high a voltage can damage the part)
  • Max. Supply Voltage (V): 5.5 (match this to your power supply; too high a voltage can damage the part)
  • Max. Operating Current (A): 10 (your supply must deliver at least this much current)
  • Product Type: USB Bridge Controllers
  • Processor Series: PL2303HX (look up this chip to confirm it runs the firmware or libraries you plan to use)
  • Max. Clock Frequency (MHz): 12.024 (make sure the rest of your system works at this frequency)
  • Interface Type: UART (confirm your cable or board uses the same connector)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

PL2303HX SSOP28 USB-to-Serial Bridge Controller IC provides a convenient solution for connecting an RS232-like full-duplex asynchronous serial device to any Universal Serial Bus (USB) capable host. PL-2303HXA highly compatible drivers could simulate the traditional COM port on most operating systems allowing the existing applications based on COM port to easily migrate and be made USB ready.

By taking advantage of USB bulk transfer mode, large data buffers, and automatic flow control, PL-2303HXA is capable of achieving higher throughput compared to traditional UART (Universal Asynchronous Receiver Transmitter) ports. When real RS232 signaling is not required, the baud rate higher than 115200 bps could be used for even higher performance. The flexible baud rate generator of PL-2303HXD could be programmed to generate any rate between 75 bps to 6M bps.

PL-2303HX is exclusively designed for mobile and embedded solutions in mind, providing a small footprint that could easily fit into any connectors and handheld devices. With very small power consumption in either operating or suspend mode, PL-2303HXA is perfect for bus-powered operation with plenty of power left for the attached devices. A flexible signal level requirement on the RS232-like serial port side also allows PL-2303HXA to connect directly to any 3.3V~1.8V range devices.

Note: Image may vary from actual product in terms of Manufacturer/Brand name according to the availability. 


  Features:

  1. Fully Compliant with USB Specification v2.0 (Full-Speed).
  2. On-Chip USB 1.1 transceiver, 5V ~ 3.3V regulator, and 12 MHz crystal oscillator.
  3. Supports RS232-like Serial Interface.
  4. Extensive Flow Control Mechanism.
  5. Configurable 512-byte bi-directional data buffer.
  6. Supports remote wake-up from MODEM input signals.
  7. Two general-purpose I/O (GPIO) pins.
  8. Optional external EEPROM for startup device configurations.
  9. Provides drivers support for Windows, Mac OS, Linux, and WinCE.
  10. Designed for Windows XP, Vista, 7 Certified Logo Drivers.
  11. USB-IF Logo Compliant with TID 40002448.
  12. Small footprint 28-pin SSOP IC package.
  13. RoHS compliant.

Package Includes:

1 x PL2303HX SSOP28 USB-to-Serial Bridge Controller IC (Revision A).

Quick specs

Manufacturer
Generic
Min Supply Voltage
3.6
Max. Supply Voltage (V)
5.5
Max. Operating Current (A)
10
Product Type
USB Bridge Controllers
Processor Series
PL2303HX
See all specifications