
1 / 3 · Click to enlarge
At a glance
This shield for arduino is a good fit for makers, students and electronics hobbyists. Main specs: model no. / name Servo Shield; no. of channels 16; resolution 12.
Key Highlights
- Model No. / Name: Servo Shield
- No. of Channels: 16
- Resolution: 12
Ideal For
- Robots and moving models
- Automation projects
- Replacement for a worn motor
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Model No. / Name | Servo Shield |
|---|---|
| No. of Channels | 16 |
| Resolution | 12 |
| Shipping Weight | 0.105 kg |
| Shipping Dimensions | 8 × 6.5 × 3 cm |
Overview
The Servo Driver Module Shield 16 Channel is listed in our shield for arduino range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Model No. / Name: Servo Shield
- No. of Channels: 16
- Resolution: 12
- Shipping Weight: 0.105 kg (important for drones, RC models and anything you carry)
- Shipping Dimensions: 8 × 6.5 × 3 cm (measure your mounting space before ordering)
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs
- It’s an I2C-controlled PWM driver with a built-in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it the signal to tie up your microcontroller, it's completely free running!
- It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
- 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs – that’s a lot of servos or LEDs
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
We wrapped up this lovely chip into a breakout board with a couple of nice extras
- Terminal block for power input (or you can use the 0.1″ breakouts on the side)
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1″ so you can only stack 4 next to each other on 0.1″ header
- “Chain-able” design
- A spot to place a big capacitor on the V+ line (in case you need it)
- 330-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
- Solder jumpers for the 6 address select pins
Features :
- The I2C input, PWM output control 16 roads, steering gear can 16 roads.
- The steering gear power independent V + input maximum 6 V.
- Logic signals and logical power independent output for 3V to 5 V.
- 40-1000 Hz frequency.
Package Includes :
1 x Servo Driver Module Shield 16 Channel.Quick specs
- Model No. / Name
- Servo Shield
- No. of Channels
- 16
- Resolution
- 12
- Shipping Weight
- 0.105 kg
- Shipping Dimensions
- 8 × 6.5 × 3 cm
Frequently Bought Together

Mega 2560 ATmega2560-16AU Board plus USB Cable compatible with Arduino
$17.99
Arduino Uno R3 with Cable
$9.99
Mega 2560 ATmega2560-16U2 Board without USB Cable for Arduino
$16.99
Uno R3 Board without Cable compatible with Arduino
$9.99
ATmel MCU ATMEGA2560-16U MEGA 2560 R3 Improved Version CH340G Board
$16.99
Uno R3 CH340G ATmega328p Development Board Compatible with Arduino
$7.99












