Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact PCF8574-based adapter that lets you drive a 16x2 or 20x4 character LCD over just two I2C wires. Contrast is adjustable on board, the backlight has its own jumper, and solder jumpers let you change the I2C address.

Key Highlights

  • PCF8574 chip converts I2C serial data to parallel LCD data
  • Works with 4-bit mode 16x2 and 20x4 character display modules
  • 5V operating voltage with a 4 g board weight
  • On-board potentiometer for contrast adjustment
  • Jumper to enable or disable the display backlight
  • Three solder jumpers allow I2C address changes from 0x3F

Ideal For

  • Arduino hobbyists adding a text display to a project
  • Students building microcontroller and electronics coursework
  • Makers who need to save I/O pins on a build
  • Bench users setting up sensor or status readouts
  • Anyone retrofitting a 16x2 or 20x4 character LCD with I2C control

Buying Tip

Confirm your character LCD module supports 4-bit mode before ordering, and remember that changing the I2C address means soldering the jumpers on the board.

Elecvora expert review

Our verdict

A simple, well-focused adapter that removes most of the wiring pain from character LCD projects. It is inexpensive and compact, though it expects you to solder headers and set addresses yourself.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Cuts LCD wiring down to power plus two I2C lines
  • On-board contrast potentiometer and backlight jumper
  • Address jumpers allow multiple displays on one bus
  • Very small and light, so it fits tight builds

Cons

  • Display module is not included
  • Address changes require soldering
  • Only suits 4-bit compatible character LCDs

Best for

Makers and students adding a character LCD to an Arduino or similar I2C-capable board

Not ideal for

Users who want a plug-and-play display with no soldering or setup

Specifications

Operating Voltage (V)5
Weight (g)4
Shipping Weight0.005 kg
Shipping Dimensions8 × 7 × 3 cm

What's in the box

  • 1 x SmartElex IIC/I2C Serial Interface Adapter Module

Frequently Asked Questions

Does this module include an LCD display?
No. The package contains only the I2C adapter module. You need a separate 16x2 or 20x4 character LCD that supports 4-bit mode.
What is the default I2C address?
The board ships with an address of 0x3F. Three solder jumpers on the board let you change it if you need to run more than one display on the same bus.
What voltage does it need?
The adapter operates from a 5V supply. Make sure your display module and host board are set up for the same 5V logic level.
How do I adjust the display contrast?
Use the potentiometer on the board. Turn it slowly while the display is powered until the characters are readable.
Can I turn the backlight off?
Yes. A jumper on the board lets you enable or disable the backlight without additional wiring.
Do I need to solder anything?
You will normally solder a pin header to connect the board, and you will need to solder the address jumpers if you want to change the I2C address.

Overview

The SmartElex IIC/I2C Serial Interface Adapter Module is a small daughter board that sits between your microcontroller and a character LCD. Instead of wiring a dozen parallel lines, you connect power and two I2C signals, and the board handles the rest. The PCF8574 IC on the board translates incoming I2C serial data into the parallel data a 4-bit character display needs.

At roughly 41.6 x 19.2 mm and only 4 g, it fits neatly behind or beside a display without adding bulk. It runs from a 5V supply and is intended for standard 16x2 and 20x4 character modules that support 4-bit mode.

Key Features

  • PCF8574 I2C expander: converts serial I2C data to parallel data for the LCD.
  • Contrast potentiometer: adjust display contrast directly on the board.
  • Backlight jumper: switch the backlight on or off without extra wiring.
  • Configurable address: three solder jumpers let you change the default 0x3F address.
  • Compact footprint: 41.6 x 19.2 mm board that mounts easily with a display.

Specifications Explained

5V operating voltage matches the supply used by most character LCD modules, so the adapter and display can share the same rail. Check that your display module is a 4-bit compatible 16x2 or 20x4 unit before connecting.

I2C address 0x3F is the factory default. If you need more than one display on the same bus, the three solder jumpers let you assign different addresses so each module can be addressed separately.

4 g weight and 41.6 x 19.2 mm size mean the board adds almost nothing to your build, which is helpful in enclosures and panel-mounted projects.

Compatibility and Requirements

The adapter is designed for character LCD modules that support 4-bit mode, including common 16x2 and 20x4 sizes. It requires a 5V supply and a host device with an I2C bus. Address changes require soldering the jumpers on the board. No display module is included, so you will need to supply your own compatible LCD.

Typical Uses

Use it for Arduino projects that need a text readout, such as sensor dashboards, clock and timer builds, menu interfaces, or status panels. It is also useful in student projects and bench setups where pin count matters and you would rather keep the wiring simple.

What's in the Box

Package contents: 1 x SmartElex IIC/I2C Serial Interface Adapter Module.

Quick specs

Operating Voltage (V)
5
Weight (g)
4
Shipping Weight
0.005 kg
Shipping Dimensions
8 × 7 × 3 cm
See all specifications