
1 / 6 · Click to enlarge
AI Summary
A 2-pack of TTP223 capacitive touch key modules that turn a light finger touch into a clean digital output. Each board has an onboard trigger LED and solder jumpers for momentary or toggle operation.
Key Highlights
- Single capacitive touch pad with onboard trigger indicator LED
- Wide 2.5 to 5 VDC operating voltage range
- Compact 14 × 10 mm board fits tight enclosures
- Solder jumpers select momentary or self-lock toggle output
- Active high or active low output selectable by pad option
- Supplied as a pack of two modules
Ideal For
- Makers building custom control panels and enclosures
- Students learning about capacitive sensing
- Hobbyists replacing mechanical push buttons
- Prop and model builders needing hidden touch inputs
- Repairers adding a simple digital input to a project
Buying Tip
Check your supply voltage and the logic level your circuit expects before soldering the jumpers, since trigger mode and output polarity are set on the board itself.
Elecvora expert review
Our verdict
A practical little module that removes the guesswork from adding a capacitive button to a project. The jumper options for momentary or toggle action and output polarity make it far more flexible than a plain switch.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Ready-assembled board with onboard trigger LED
- Flexible trigger mode and output polarity options
- Wide 2.5 to 5 VDC supply range
- Very small 14 × 10 mm footprint
- Two modules supplied per pack
Cons
- Changing modes requires soldering the jumper pads
- No cables or headers included
- Sensing behaviour must be re-checked after each mode change
Best for
Makers and students who need a compact touch input for a custom build
Not ideal for
Users who want a plug-and-play button with pre-fitted wiring
Specifications
| Item Type | Keypad Module |
|---|---|
| Operating Voltage (VDC) | 2.5 to 5 |
| Length (mm) | 14 |
| Width (mm) | 10 |
| Weight (g) | 0.6 |
| Shipping Weight | 0.085 kg |
| Shipping Dimensions | 3 × 3 × 1 cm |
What's in the box
- 2 × TTP223 touch key modules
Frequently Asked Questions
How many modules are included?
What voltage does it need?
Can I make it stay on after a touch?
Can the output be inverted?
Why does the module ignore touches just after power-up?
Does it work through a panel?
Overview
The TTP223 touch key module is a small, assembled board built around the TTP223 capacitive touch detector IC. Instead of a moving mechanical contact, it senses a finger near its touch area and switches its output accordingly. Each board provides one integrated touch pad of roughly 11 × 10.5 mm, and an onboard LED gives a visual indication whenever the sensor is triggered.
This listing supplies two modules, which is handy when you want a matching pair of inputs, a spare for testing, or two buttons on the same panel.
Key Features
- Single-button capacitive sensing with no moving parts
- Onboard LED shows trigger state at a glance
- Solder jumpers allow momentary or self-lock toggle behaviour
- Output polarity can be set active high or active low
- Runs from 2.5 to 5 VDC
- Small footprint of 14 × 10 mm and 0.6 g per module
Specifications Explained
Operating voltage 2.5 to 5 VDC means the board can share a supply with most low-voltage hobby electronics, including 3.3 V and 5 V systems, without an extra regulator.
Dimensions of 14 × 10 mm describe the board outline, while the sensing area itself is about 11 × 10.5 mm. That leaves very little wasted space around the pad, so the module can sit behind a thin panel with only the touch zone exposed.
Trigger mode jumpers are the most useful detail. In the default no-lock setting the output follows your touch, returning to its idle state when you release. In self-lock mode each touch changes the output state and it stays there until the next touch, giving you a push-on, push-off action.
Output polarity can also be changed, so the module can idle high and go low, or idle low and go high, depending on what the receiving circuit expects.
Compatibility and Requirements
The module needs a DC supply within its 2.5 to 5 VDC range and a connection to the output pin of the circuit it is controlling. Changing trigger mode or output polarity requires soldering the small jumper pads on the board. After power-up the sensor needs a short settling period, during which the keypad should not be touched, and it re-calibrates automatically when left untouched.
Typical Uses
- Touch buttons on homemade control panels and enclosures
- Replacing a worn mechanical push button with a sealed touch pad
- Student and hobby projects that need a simple digital input
- Interactive displays, props and model builds
- Bench testing touch-sensing ideas before a final design
What's in the Box
Two TTP223 touch key modules. No cables, headers or instructions are included.


Quick specs
- Item Type
- Keypad Module
- Operating Voltage (VDC)
- 2.5 to 5
- Length (mm)
- 14
- Width (mm)
- 10
- Weight (g)
- 0.6
- Shipping Weight
- 0.085 kg
















