Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A small vibration switch module built around the SW-18015P sensor, which briefly conducts when shaken or tapped from any angle. It gives Arduino projects a simple, low-cost way to detect shock and movement.

Key Highlights

  • SW-18015P vibration switch at the heart of the module
  • Omni-directional design triggers from any mounting angle
  • Compact 20 x 15 mm PCB fits tight enclosures
  • Three-pin layout for GND, +5 V and signal
  • 12 VDC operating voltage for low-current trigger circuits
  • Lightweight module, about 8 g shipping weight

Ideal For

  • Arduino beginners learning digital sensor inputs
  • Students building motion or shock detection projects
  • Makers adding a simple vibration trigger to small enclosures
  • Hobbyists prototyping interactive toys and gadgets
  • Robot builders needing a compact shock sensor

Buying Tip

Confirm your project only needs a brief on/off trigger rather than continuous vibration measurement, since this module reports momentary contact events.

Elecvora expert review

Our verdict

A no-frills vibration switch module that does one job well: turning a shake or tap into a momentary signal. It is a sensible low-cost part for Arduino learners and small prototypes.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Works from any angle, so mounting is easy
  • Very compact 20 x 15 mm board
  • Simple three-pin wiring
  • Low cost for a starter sensor

Cons

  • Output is momentary, not a measured vibration level
  • Suited only to low-current circuits
  • Jumper wires and Arduino board not included

Best for

Arduino beginners and makers needing a simple shock trigger

Not ideal for

Projects that need precise or continuous vibration measurement

Specifications

Model No. / NameVibration Sensor Module
Operating Voltage (VDC)12
Component TypeSW-18015P
Heater Current20mA
PCB Size ( L x W ) mm20 x 15
Shipping Weight0.008 kg
Shipping Dimensions3 × 3 × 3 cm

What's in the box

  • 1 x Vibration Switch Module

Frequently Asked Questions

How do I connect this module to an Arduino?
Connect the ground pin to GND, the middle pin to +5 V and the S signal pin to a digital input such as pin 10. You will need your own jumper wires.
Does the sensor work in any orientation?
Yes. The SW-18015P switch is omni-directional, so any angle can trigger it.
What voltage does the module use?
The module is rated for 12 VDC operation, and the signal pin is intended for an Arduino input. Check your circuit against the rated voltage before powering it.
Is the output continuous or momentary?
The switch rests open and conducts only briefly when disturbed, returning to the open state once the movement stops.
What is included in the package?
The package contains one vibration switch module. Jumper wires and an Arduino board are not included.
Can it switch a motor or lamp directly?
No. With a 20 mA heater current rating it is intended for small, low-current trigger circuits only.

Overview

The Elecvora Vibration Switch Sensor Module is a small breakout board built around the SW-18015P vibration switch. In its resting state the switch is open, so the signal line stays inactive. When the sensor is tapped, shaken or otherwise disturbed with enough force, the internal conductive element makes brief contact and the module outputs a momentary change that a microcontroller can read. Once the movement stops, the switch returns to its open state.

Because the sensor works from any direction, you do not have to align it carefully inside your build. That makes it a practical choice for quick prototypes, student projects and small devices where a simple shock or motion trigger is all you need.

Key Features

  • SW-18015P sensor: a well-known vibration switch type used in maker projects.
  • Omni-directional response: any angle can trigger the switch, so mounting orientation is flexible.
  • Compact board: the PCB measures 20 x 15 mm, small enough for tight enclosures.
  • Simple wiring: three pins for ground, +5 V and signal.
  • Lightweight: shipping weight is about 0.008 kg, so it adds almost nothing to your build.

Specifications Explained

Operating voltage

The module is rated for 12 VDC operation. In practice, the signal pin is intended to connect to an Arduino input such as pin 10, while the supply pin connects to the Arduino +5 V rail. Check your own circuit design against the rated voltage before powering it up.

Current rating

The 20 mA heater current figure tells you this is a small-signal device. It is suited to low-current trigger circuits rather than switching motors, lamps or other heavy loads directly.

Physical size

At 20 x 15 mm the PCB is easy to place in handheld gadgets, small robots and custom enclosures. Shipping dimensions of 3 x 3 x 3 cm reflect the compact packaging.

Compatibility and Requirements

The module is designed for Arduino boards. Wiring is straightforward: connect the pin marked with the ground symbol to GND, the middle pin to +5 V, and the S signal pin to a digital input such as pin 10. You will need your own jumper wires and a suitable Arduino board, neither of which is included.

Typical Uses

  • Shock and tap detection in Arduino learning projects
  • Simple motion-triggered alarms or indicators
  • Vibration sensing in small robots and prototypes
  • Interactive toys and handheld devices
  • Trigger inputs for low-current circuits

What's in the Box

The package includes one vibration switch module. Jumper wires, an Arduino board and other project parts are not included.

Quick specs

Model No. / Name
Vibration Sensor Module
Operating Voltage (VDC)
12
Component Type
SW-18015P
Heater Current
20mA
PCB Size ( L x W ) mm
20 x 15
Shipping Weight
0.008 kg
See all specifications