
1 / 3 · Click to enlarge
AI Summary
A compact 9-DoF AHRS and IMU module that fuses accelerometer, gyroscope and magnetometer data into stable roll, pitch and heading readings. It is pre-calibrated, starts in about 500 ms and suits static alignment and tilt monitoring tasks.
Key Highlights
- 9-DoF sensor suite with accelerometer, gyroscope and magnetometer fusion
- Stable roll, pitch and heading output for static and low-motion work
- Configurable output rate up to 200 Hz with roughly 10 ms latency
- Fast startup of about 500 ms and pre-calibrated from the factory
- Wide 2.7 to 5.5 V operating range with 60 mA average current
- Compact board measuring about 28.76 by 27.86 mm and weighing 14 g
Ideal For
- Solar installers setting panel tilt and row alignment
- Field engineers aligning antennas and satellite dishes
- Industrial integrators checking machine and fixture orientation
- Technicians logging tilt and heading on rooftop equipment
- Makers building static orientation or levelling projects
Buying Tip
Check that your host supply and I/O levels match the module's stated voltage windows before wiring, and allow current headroom for the 100 mA peak draw.
Elecvora expert review
Our verdict
The YDx M CB-2-E is a sensible choice when you need dependable roll, pitch and heading readings in static or slow-moving setups rather than fast dynamics. Its factory calibration and quick startup reduce integration effort for alignment and monitoring work.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Pre-calibrated and tested for out-of-the-box consistency
- Fast 500 ms startup with around 10 ms latency
- Configurable output up to 200 Hz
- Compact, lightweight board with tool-free installation
Cons
- Optimised for static and low-dynamic use, not fast motion
- No cables included beyond four connecting pins
- Operating range limited to −10 to +60 °C
Best for
Static alignment, tilt setup and orientation monitoring
Not ideal for
High-speed or highly dynamic motion tracking
Specifications
| Sensor Type | Strain Gauge Based Load Cell |
|---|---|
| Length (mm) | 28.76 |
| Weight (g) | 14 |
| I/O pin voltage | 3.18 to 3.42 V |
| Width (mm) | 27.86 |
| Operating Voltage (V) | 2.7~5.5 |
| Max. output | 200 Hz |
| Dimensions (L x W x H) mm | 170 x 130 x 130 |
| Avg. Current Consumption | 60 mA |
| Installation | Tool-Free, Easy Replacement |
| Supply Voltage | 4.60 to 5.40 V |
| Peak Current (mA) | 100 |
| Operating Temperature (°C) | −10 to +60 |
| Shipping Weight | 0.136 kg |
| Shipping Dimensions | 14 × 11 × 4 cm |
What's in the box
- 1 x Yaanendriya YDx M CB-2-E 9-DoF AHRS and IMU Module
- 4 x Connecting Pin
Frequently Asked Questions
What does the 9-DoF sensor suite include?
What voltage does the module need?
How much current does it draw?
Is the module calibrated before shipping?
What is included with the module?
What environment is it suited to?
Overview
The Yaanendriya YDx M CB-2-E is a 9-DoF AHRS and IMU module designed for orientation measurement where consistency matters more than speed. It pairs an accelerometer, a gyroscope and a magnetometer with Yaanendriya's sensor fusion algorithm to produce roll, pitch and heading values. Rather than chasing high-speed motion, the module is tuned for static and low-dynamic conditions, so readings stay repeatable when you are aligning, installing or monitoring equipment.
Every unit is calibrated and tested in-house before dispatch, which means you can integrate it without a lengthy calibration routine. Startup takes roughly 500 ms and latency is around 10 ms, keeping the data responsive enough for setup and logging work.
Key Features
- 9-DoF sensing: accelerometer, gyroscope and magnetometer combined for full orientation data.
- Fusion-based output: roll, pitch and heading delivered through Yaanendriya's fusion algorithm.
- Configurable rate: output can be set up to 200 Hz to match your sampling needs.
- Fast wake-up: approximately 500 ms startup with about 10 ms latency.
- Compact footprint: about 28.76 by 27.86 mm and only 14 g, easy to fit into tight enclosures.
- Tool-free installation: designed for straightforward replacement and mounting.
Specifications Explained
The operating voltage range of 2.7 to 5.5 V gives flexibility when powering from common logic supplies, while the supply voltage window of 4.60 to 5.40 V and I/O pin voltage of 3.18 to 3.42 V tell you how to plan the interface. Average current consumption is 60 mA with peaks up to 100 mA, so size your regulator with a little headroom.
The 200 Hz maximum output rate is useful for capturing tilt changes during setup, and the 10 ms latency keeps feedback timely. The module is rated for −10 to +60 °C, which covers most indoor and sheltered outdoor installation work. Its small 14 g body and roughly 28 mm dimensions make it simple to place near the point you are measuring.
Compatibility and Requirements
Plan for a supply that sits within the stated voltage windows and an I/O level near 3.18 to 3.42 V. The board is intended for integrators who will wire it into their own system; no additional cables beyond the supplied connecting pins are included. Confirm that your host can accept the module's output rate up to 200 Hz before finalising your data pipeline.
Typical Uses
- Antenna and satellite dish azimuth alignment
- Solar panel tilt and orientation setup
- Building frame and structural alignment checks
- Rooftop equipment heading and tilt measurement
- Industrial machine and fixture alignment
- Camera and LiDAR static mounting alignment
What's in the Box
1 x Yaanendriya YDx M CB-2-E 9-DoF AHRS and IMU Module and 4 x connecting pins.
Quick specs
- Sensor Type
- Strain Gauge Based Load Cell
- Length (mm)
- 28.76
- Weight (g)
- 14
- I/O pin voltage
- 3.18 to 3.42 V
- Width (mm)
- 27.86
- Operating Voltage (V)
- 2.7~5.5















