
1 / 3 · Click to enlarge
AI Summary
A 4-pin female single row housing connector on a 5.08mm pitch, supplied with a 300mm 24 AWG wire already attached. It saves time on wire-to-board runs by arriving ready to fit instead of needing separate crimping.
Key Highlights
- 4-pin female single row housing on a 5.08mm pitch
- 300mm wire pre-attached for immediate installation
- 24 AWG conductor keeps the lead light and flexible
- Insulation resistance rated at 10 MOhm or higher
- Suits wire-to-board power and signal connections
- Compact single-unit pack for spares and repairs
Ideal For
- Makers building wire-to-board connections on 5.08mm headers
- Drone and RC hobbyists doing internal rewiring
- FPV builders who need a short pre-wired lead
- Repair technicians replacing damaged connector leads
- Electronics students learning connector and wiring practice
Buying Tip
Confirm your PCB header uses a 5.08mm pitch and four single-row positions before ordering, since this female housing will only mate with a matching male header.
Elecvora expert review
Our verdict
A sensible pre-wired connector for anyone working with 5.08mm four-way headers, since the lead arrives ready to fit. It is a simple part, but the pre-attached 24 AWG wire removes a fiddly crimping step.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Wire already attached, so no crimping tools needed
- Clear 5.08mm pitch suits wider-spaced headers
- Four-pin single row layout is easy to align
- Insulation resistance rated at 10 MOhm or higher
Cons
- Board-side male header is not included
- No voltage or current rating is stated in the data
- Wire gauge is fixed at 24 AWG, limiting heavier loads
Best for
Builders making removable four-way wire-to-board connections on a 5.08mm pitch
Not ideal for
High-current power runs or boards with 2.54mm headers
Specifications
| Manufacturer | ZGWD |
|---|---|
| Pitch Spacing (mm) | 5.08 |
| No. of Pins | 4 |
| Wire Length(mm) | 300 |
| Allowed Wire Size (AWG) | 24 |
| Insulation Resistance (MOhm) | ≥ 10MΩ |
| Shipping Weight | 0.001 kg |
| Shipping Dimensions | 1 × 1 × 1 cm |
What's in the box
- 1 x P-04P 5.08mm 4-pin female single row housing connector with 300mm 24 AWG wire
Frequently Asked Questions
What is this connector used for?
Will it fit a 2.54mm header?
Is the board-side header included?
What wire gauge and length does it use?
What is the insulation resistance?
How should I care for it?
Overview
The ZGWD P-04P is a female housing connector with four pins arranged in a single row on a 5.08mm pitch. It arrives with a 300mm length of 24 AWG wire already fitted, which makes it a convenient building block when you need to bring wiring to a PCB without preparing crimps from scratch.
Because the housing and lead come as one unit, the part is useful for anyone who wants a repeatable connection point rather than a loose set of terminals. The 5.08mm spacing gives generous separation between contacts, and the four-pin layout covers small power and signal groupings in one connector body.
Key Features
- Female housing design: accepts a matching male header or pin arrangement on the board side.
- 5.08mm pitch: wider contact spacing for layouts that call for it.
- Four pins, single row: a compact linear contact group in one housing.
- 300mm wire lead: enough length to route inside a typical enclosure.
- 24 AWG wire: a light, flexible conductor size for internal wiring.
- Insulation resistance: rated at 10 MOhm or higher.
Specifications Explained
Pitch spacing
The 5.08mm pitch is the distance between the centre of one pin and the next. It matters because the mating header on your PCB must use the same spacing; a 5.08mm housing will not seat on a 2.54mm header. Check your board footprint before ordering.
Pin count and row configuration
Four pins in a single row means all contacts sit in one line. That keeps the connector narrow and makes it easy to align with a matching four-way header.
Wire length and gauge
The 300mm lead gives useful reach for internal routing, while 24 AWG is a common size for low-current wiring inside devices. The gauge is fixed at 24 AWG, so plan current draw accordingly rather than treating it as a high-power lead.
Insulation resistance
A rating of 10 MOhm or above describes how well the insulation resists leakage between conductors. In practice it supports clean signal and low-current power paths.
Compatibility and Requirements
This is a female housing, so it is intended to mate with a corresponding male header or pin set on a 5.08mm pitch with four positions in a single row. The board side is not included. No voltage or current rating is specified in the product data, so confirm suitability for your circuit before use. The wire is pre-attached; terminating the free end to your circuit is the installer's task.
Typical Uses
- Wire-to-board power and signal links inside electronic devices
- Internal wiring in drones, RC models and FPV builds
- Repair and replacement leads in tools and small gadgets
- Prototyping and bench assemblies needing a removable connection
- General electronic assemblies where a four-way lead is handy
What's in the Box
One P-04P 5.08mm 4-pin female single row housing connector with a 300mm 24 AWG wire attached.
Quick specs
- Manufacturer
- ZGWD
- Pitch Spacing (mm)
- 5.08
- No. of Pins
- 4
- Wire Length(mm)
- 300
- Allowed Wire Size (AWG)
- 24
- Insulation Resistance (MOhm)
- ≥ 10MΩ



















