
1 / 3 · Click to enlarge
AI Summary
A 6-pin female housing connector with a 2.00mm pitch and 300mm of 28 AWG wire already attached. It saves you the crimping step and gives a secure wire-to-board link for signal and low-current wiring.
Key Highlights
- 6-pin female housing in a 2.00mm pitch layout
- 300mm pre-attached 28 AWG wire on every unit
- Wire-to-board design for signal and low-current links
- Plastic housing with metal terminals for a secure fit
- Ready to route, no separate crimping step needed
- Compact and lightweight for tight electronic assemblies
Ideal For
- Electronics hobbyists building compact prototypes
- Repair technicians replacing pre-wired harness links
- Small-batch assemblers needing repeatable 2.00mm wiring
- Makers wiring signal lines on development boards
- Anyone working with 2.00mm-pitch wire-to-board connections
Buying Tip
Confirm your board header is a 6-pin, 2.00mm-pitch male connector before ordering, since a 2.54mm header will not mate with this housing.
Elecvora expert review
Our verdict
A tidy, ready-to-use pre-wired connector that saves time on harness work for 2.00mm-pitch signal wiring. It is a practical consumable rather than a premium part, and it does its job well when matched to the right header.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Wires already attached, so no crimping step
- Compact 6-pin, 2.00mm layout
- Useful 300mm cable length
- Flexible 28 AWG wire for tight routing
Cons
- Only mates with 2.00mm-pitch headers
- Free ends are unterminated and need your own connection method
- Thin 28 AWG gauge suits signals, not higher-current loads
Best for
Signal and low-current wiring in compact 2.00mm-pitch builds
Not ideal for
Higher-current power runs or 2.54mm-pitch headers
Specifications
| Shipping Weight | 0.001 kg |
|---|---|
| Shipping Dimensions | 1.0 × 1.0 × 1.0 cm |
What's in the box
- 1 x PA-06Y 2.00mm 6-pin Female Housing Connector with 300mm Wire (28 AWG)
Frequently Asked Questions
What pitch does this connector use?
How many pins does it have?
What wire length and gauge are included?
Can I use it for power?
What is included in the package?
How should I care for the connector?
Overview
The ZGWD PA-06Y is a female housing connector supplied with wires already attached. It uses a 2.00mm pitch and a 6-pin configuration, with 300mm of 28 AWG cable fitted to the housing. The part is intended for wire-to-board connections carrying signals or low-current loads, and it combines a plastic housing with metal terminals to hold each wire in place.
Because the cable comes pre-attached, this connector removes one of the more fiddly steps in harness building. You can focus on routing, terminating the free ends, and plugging the housing into its mating header.
Key Features
- Pre-wired construction: 300mm of 28 AWG wire is fitted to the housing, ready for your project.
- 6-pin, 2.00mm pitch: a compact layout for dense boards and small enclosures.
- Female housing: designed to mate with a corresponding 2.00mm-pitch header in wire-to-board setups.
- Plastic housing with metal terminals: a straightforward, serviceable connector build.
- Signal and low-current use: suited to control lines, sensing leads, and similar low-power wiring.
Specifications Explained
2.00mm pitch is the centre-to-centre spacing between adjacent pins. It sits between the larger 2.54mm spacing common on prototyping boards and the finer pitches used in very compact electronics, so check that your mating header matches this spacing before ordering.
6 pins gives you six separate conductors in one housing. That is handy when several signal lines need to travel together and stay in a fixed order.
28 AWG wire is a thin gauge that keeps the cable flexible and easy to route in tight spaces. It is intended for signal and low-current connections rather than high-power runs.
300mm length provides a useful working span between the board and the next connection point without leaving large loops of excess cable.
Female housing means the connector accepts mating pins from the board side. Confirm the gender and pitch of your existing header so the two parts engage correctly.
Compatibility and Requirements
This connector is built for wire-to-board use at a 2.00mm pitch with a 6-pin female housing. It requires a compatible 2.00mm-pitch mating header on the board side. The free wire ends are unterminated, so you will need to connect them to your circuit by your preferred method. No datasheet values beyond the listed specifications are provided here; refer to the product attachments for further technical detail.
Typical Uses
- Signal wiring inside small electronic assemblies
- Low-current connections on prototype and development boards
- Replacement or repair of pre-wired harness links
- Compact device wiring where a 2.00mm pitch is required
What's in the Box
1 x PA-06Y 2.00mm 6-pin Female Housing Connector with 300mm Wire (28 AWG).



















