Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A white nylon module 1 spur gear with 46 teeth, a 5.71 mm bore and 47.81 mm outer diameter, weighing just 8 g. It runs quietly without lubrication, making it a simple replacement or prototype gear for light-duty mechanisms.

Key Highlights

  • Module 1 spur gear with 46 teeth for standard pitch matching
  • Moulded nylon body runs quietly and absorbs vibration
  • No lubrication required for typical light-duty use
  • 8 g weight keeps rotating assemblies light
  • 5.71 mm bore and 46 mm mounting hole PCD
  • White colour makes tooth wear and debris easy to spot

Ideal For

  • Hobby builders assembling small module 1 gear trains
  • Makers prototyping light-duty mechanisms
  • Repairers replacing a worn 46-tooth nylon gear
  • Students and educators demonstrating gear ratios
  • Designers needing a light, quiet gear for compact assemblies

Buying Tip

Confirm the mating gear is also module 1 and measure your shaft against the 5.71 mm bore before ordering.

Elecvora expert review

Our verdict

A straightforward nylon spur gear that suits light-duty builds where weight and noise matter more than load capacity. Its published dimensions make matching to an existing module 1 gear train reasonably easy.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Light at 8 g
  • Quiet running with no lubrication needed
  • Clear, complete dimensional data
  • Corrosion-resistant nylon body

Cons

  • Not suited to high-torque or heavy loads
  • Pressure angle not stated, so mating gear must be verified
  • No shaft or fasteners included

Best for

Light-duty hobby and prototype gear trains

Not ideal for

High-load industrial power transmission

Specifications

Model No. / Name1M-46T-6-46
Gear StructureSpur
Pitch (Module)1
No. of Teeth46
Face Width (FW) mm4.85
Total Width (W)8.47
Internal Diameter(ID)(mm)5.71
Outer Diameter (mm)47.81
Mounting Hole PCD (mm)46
Gear MaterialNylon
ColorWhite
Weight (g)8
Shipping Weight0.012 kg
Shipping Dimensions9 × 6 × 3 cm

What's in the box

  • 1 x Nylon Spur Gear (1M-46T-6-46)

Frequently Asked Questions

What does 1M-46T-6-46 mean?
It is the model reference: module 1 pitch, 46 teeth, with the remaining figures relating to the gear's dimensions as listed in the specifications.
What shaft size does it fit?
The internal diameter is 5.71 mm, so it is intended for a shaft or hub of that size. Measure your shaft before fitting.
Does it need lubrication?
Nylon gears are typically run without lubrication in light-duty service. Keep the gear clean and free of abrasive debris.
Can it replace a metal gear?
It can in low-load applications where noise and weight matter, but nylon is not a like-for-like substitute for high-torque metal gears.
What is included in the package?
One nylon spur gear, model 1M-46T-6-46. No shaft, fasteners or lubricant are included.
How should I store it?
Keep it in a dry place away from heat and direct sunlight, and avoid dropping it, since nylon teeth can chip under impact.

Overview

The 1M-46T-6-46 is a white nylon spur gear built to a module 1 pitch with 46 teeth. It measures 47.81 mm across its outer diameter and has a 5.71 mm internal diameter, so it fits onto a matching shaft or hub. At only 8 g, it adds very little mass to a small gear train.

Nylon gears are widely chosen where metal gears would be unnecessarily heavy or noisy. This gear runs quietly, damps vibration and does not need lubrication in normal light-duty service, which keeps maintenance simple.

Key Features

  • Module 1 pitch: a common metric gear standard that simplifies matching with other module 1 gears.
  • 46 teeth: a defined tooth count for calculating ratio and centre distance in your assembly.
  • Nylon construction: light, quiet running and resistant to corrosion compared with metal alternatives.
  • Compact dimensions: 4.85 mm face width and 8.47 mm total width suit tight spaces.
  • Mounting reference: a 46 mm mounting hole pitch circle diameter helps with hub or carrier alignment.

Specifications Explained

Module 1 describes the tooth size. Gears with the same module and pressure angle mesh correctly, so this value is the first thing to check against the gear it will run with.

46 teeth sets the gear ratio once paired with another gear. Combined with the 47.81 mm outer diameter, it lets you work out centre distances for a two-gear layout.

Face width of 4.85 mm is the toothed contact width, while the 8.47 mm total width includes the hub area. Check both against your available space and the width of the mating gear.

The 5.71 mm internal diameter is the bore that accepts the shaft, and the 46 mm mounting hole PCD gives a reference circle for fixing or aligning the gear on a carrier.

Compatibility and Requirements

This gear meshes with other module 1 gears of a compatible pressure angle; that detail is not stated in the available data, so verify it against your mating part. The shaft or hub you mount it on must suit the 5.71 mm bore. No fasteners, shaft, lubricant or additional hardware are included, so plan for those separately.

Typical Uses

Small gear trains in hobby mechanisms, prototype assemblies, light-duty drives and educational builds are natural applications. It can also serve as a replacement part where a module 1, 46-tooth nylon gear has worn or broken.

What's in the Box

One nylon spur gear, model 1M-46T-6-46.

Quick specs

Model No. / Name
1M-46T-6-46
Gear Structure
Spur
Pitch (Module)
1
No. of Teeth
46
Face Width (FW) mm
4.85
Total Width (W)
8.47
See all specifications