
1 / 5 · Click to enlarge
AI Summary
A compact Adafruit time-of-flight module that measures 30mm to 4000mm using an invisible 940nm laser and a narrow 27 degree sensing cone. It runs on 3V or 5V over I2C with solder-free STEMMA QT / Qwiic connectors.
Key Highlights
- Time-of-flight measurement from roughly 30mm up to 4000mm
- Narrow 27 degree field of view for clearer target sensing
- Onboard regulator and level shifting for 3V to 5V logic
- I2C interface at up to 400kHz, default address 0x29
- STEMMA QT / Qwiic connectors for solder-free wiring
- Update rate up to 50Hz for responsive distance readings
Ideal For
- Robotics builders adding obstacle or proximity sensing
- Automation and control projects needing fast distance feedback
- Interactive installation and gadget makers
- Arduino, Raspberry Pi and CircuitPython users
- Makers who prefer solder-free STEMMA QT / Qwiic wiring
Buying Tip
Check that your project can mount the sensor with a clear view of the target, since the narrow 27 degree cone needs a direct line of sight to read reliably.
Elecvora expert review
Our verdict
A well-rounded time-of-flight module that balances a useful 30mm to 4000mm range with fast 50Hz readings and easy 3V to 5V integration. The narrow beam and solder-free connectors make it a practical choice for robotics and interactive builds.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Wide 30mm to 4000mm measurement span
- Narrow 27 degree field of view reduces ambiguity
- 3V and 5V logic support with onboard regulation
- STEMMA QT / Qwiic connectors simplify wiring
- Up to 50Hz update rate
Cons
- Range at the far end depends on target and lighting conditions
- Requires a host microcontroller and I2C setup
- Header pin must be soldered for breadboard use
Best for
Robotics, automation and interactive projects needing compact, fast distance sensing
Not ideal for
Projects needing a very wide sensing area or a fully enclosed, pre-wired module
Specifications
| Shipping Weight | 0.005 kg |
|---|---|
| Shipping Dimensions | 8 × 6 × 1 cm |
What's in the box
- 1 x Adafruit VL53L1X Time of Flight Distance Sensor - ~30 to 4000mm - STEMMA QT / Qwiic
- 1 x Header pin
Frequently Asked Questions
What range can this sensor measure?
Does it work with 5V boards?
How do I connect it to my board?
Can I use more than one sensor at once?
What is included in the package?
What is the update rate?
Overview
The Adafruit VL53L1X is a time-of-flight distance sensor that calculates range by measuring how long an invisible 940nm laser takes to travel to a target and reflect back. Because it times the light rather than judging intensity, it gives consistent readings across a wide span of roughly 30mm to 4000mm. The 27 degree typical field of view keeps the sensing cone narrow, which reduces the ambiguity that wider IR and ultrasonic sensors sometimes report.
Key Features
- Time-of-Flight sensing: direct distance measurement using a 940nm invisible laser.
- Wide range: approximately 30mm to 4000mm depending on target and conditions.
- Fast updates: readings at up to 50Hz for responsive projects.
- Flexible power: onboard regulator and logic level shifting support 3V and 5V systems.
- Simple wiring: I2C at up to 400kHz with STEMMA QT / Qwiic connectors.
- Extra control: shutdown and interrupt pins are broken out for timing and power management.
Specifications Explained
The 30mm to 4000mm range is the headline figure, but real results depend on the target surface and ambient light, so treat the outer end as a best-case figure. The 27 degree field of view means the sensor looks at a relatively tight area, which helps when you want to measure one object rather than everything nearby. An update rate of up to 50Hz is fast enough for movement tracking and control loops without flooding your bus. The default I2C address of 0x29 is changeable, which matters if you want more than one sensor on the same bus. Logic compatibility from 3V to 5V means the board can sit directly on common microcontroller pins.
Compatibility and Requirements
The module works with 3V and 5V logic and communicates over I2C, so it pairs with boards such as Arduino, Raspberry Pi and CircuitPython devices. STEMMA QT / Qwiic connectors allow solder-free connection to matching cables and breakout boards; otherwise the included header pin can be soldered for breadboard or jumper-wire use. You will need a host microcontroller and a suitable I2C connection.
Typical Uses
Useful for robotics and obstacle detection, automation and level or presence sensing, and interactive electronics where a compact, fast distance reading is needed. The narrow beam also suits projects that need to target a specific zone rather than a broad area.
What's in the Box
- 1 x Adafruit VL53L1X Time of Flight Distance Sensor - ~30 to 4000mm - STEMMA QT / Qwiic
- 1 x Header pin



















