
1 / 3 · Click to enlarge
AI Summary
A compact 220 V AC module that closes a normally open relay contact a set time after power is applied, then releases it. Its passive dry contact output makes it easy to wire into existing control circuits.
Key Highlights
- 220 V AC nominal supply with wide 100-250 V operating range
- Normally open passive relay output works like a dry contact switch
- Adjustable delay before relay closes and adjustable contact duration
- Onboard indicator flashes during delay and stays on while relay is closed
- Compact 44 x 42 mm PCB with low 0.8 W power consumption
- Industrial-grade microcontroller for accurate, stable timing
Ideal For
- Makers and installers building automatic power-on sequences
- Technicians adding delayed relay switching to mains-powered equipment
- Automation hobbyists needing a passive dry contact trigger
- Repair and retrofit projects where a compact timer module fits
Buying Tip
Confirm your equipment can be controlled by a passive normally open contact, since the module does not supply any output voltage itself.
Elecvora expert review
Our verdict
A practical little module for adding a timed, automatic contact closure after power-up, especially where a passive output is preferred. It is simple and compact, but it is a bare board for mains wiring rather than a finished consumer product.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Passive dry contact suits many control arrangements
- Wide 100-250 V operating range
- Adjustable delay and contact duration
- Compact 44 x 42 mm PCB
Cons
- Exposed mains wiring requires care and a suitable enclosure
- Timing must be set by the user, with no digital display mentioned
- No output voltage, so the controlled device needs its own supply
Best for
Installers and makers needing delayed automatic relay switching after mains power-on
Not ideal for
Users looking for a plug-and-play consumer timer with a built-in socket
Specifications
| Model No. / Name | RD01AC |
|---|---|
| Material | PCB |
| Supply Voltage | 220 V AC |
| Power Consumption (W) | 0.8 |
| Operating Current (mA) | 80mA 5V; 45mA 12V; 25mA 24V |
| Output form | NO COM (one set of normally open passive output) |
| Length (mm) | 44 |
| Width (mm) | 42 |
| Shipping Weight | 0.036 kg |
| Shipping Dimensions | 8 × 5 × 3 cm |
What's in the box
- 1 x Device Power-on Automatic Boot Module 220V Wide Voltage RD01AC
Frequently Asked Questions
What does the RD01AC actually do?
Does the module output a voltage?
What supply voltage does it need?
Can I adjust the delay time?
What is included with the module?
How should I handle and install it?
Overview
The RD01AC is a single-channel automatic power-on module built on a compact PCB. Its job is simple: when mains power is applied, it waits for a preset delay, closes a normally open relay contact for a preset duration, and then opens it again. This gives connected equipment a controlled startup sequence without manual intervention.
The module is powered directly from AC mains and uses an RC step-down supply, so there is no separate low-voltage supply to wire in. A power indicator flashes during the delay period, stays continuously lit while the relay is closed, and turns off when the cycle is complete.
Key Features
- Wide voltage operation: rated for 220 V AC supply and usable from approximately 100 V to 250 V.
- Passive dry contact output: one set of normally open contacts (NO COM) behaves like a switch and carries no voltage of its own.
- Adjustable timing: both the delay before closing and the relay-on duration can be set.
- Industrial-grade control chip: provides accurate timing and strong anti-interference performance.
- Low consumption: 0.8 W typical power draw.
- Compact board: 44 mm long and 42 mm wide.
Specifications Explained
Supply voltage: the module is designed around a 220 V AC supply but the manufacturer states it can be used from about 100 V to 250 V, which covers many international mains systems.
Operating current: current draw depends on the supply voltage, quoted at 80 mA at 5 V, 45 mA at 12 V and 25 mA at 24 V in the supplied data.
Output form: NO COM means a single normally open contact pair. Because it is passive, it does not output a voltage; it simply closes or opens a circuit, so the device being controlled needs its own supply.
Power consumption: 0.8 W, low enough for continuous standby operation.
Compatibility and Requirements
Because the output is a dry contact, the module can switch or trigger a wide range of equipment provided the contact is wired correctly and the load is compatible with the relay contact. The module itself needs an AC mains supply within the stated range. Wiring should only be carried out by someone competent to work with mains voltage, with the supply isolated first.
Typical Uses
Common applications include automatic startup of equipment after a power interruption, delayed switching of lights or appliances, and triggering control inputs on devices that expect a dry contact signal. It is also useful where a short pulse or timed contact closure is needed after power-on.
What's in the Box
- 1 x Device Power-on Automatic Boot Module 220V Wide Voltage RD01AC
Quick specs
- Model No. / Name
- RD01AC
- Material
- PCB
- Supply Voltage
- 220 V AC
- Power Consumption (W)
- 0.8
- Operating Current (mA)
- 80mA 5V; 45mA 12V; 25mA 24V
- Output form
- NO COM (one set of normally open passive output)













