Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A single-channel 100 MHz oscilloscope probe with switchable 1X/10X attenuation and a 1.2 m cable. Its sub-3.5 ns rise time and adjustable compensation help keep fast signal edges accurate on most standard scopes.

Key Highlights

  • 100 MHz bandwidth for a wide range of signal measurements
  • Switchable 1X and 10X attenuation for low and high-frequency work
  • Rise time under 3.5 ns to preserve fast edge detail
  • 1MΩ input resistance matches common oscilloscope inputs
  • Adjustable compensation from 10pF to 30pF for scope matching
  • 1.2 m cable for flexible bench and chassis testing

Ideal For

  • Electronics hobbyists working on prototype and repair projects
  • Students learning oscilloscope measurement basics
  • Technicians diagnosing digital and analog signals
  • Makers who need a spare or replacement scope probe

Buying Tip

Check your oscilloscope's input capacitance before buying; the probe's 10pF to 30pF compensation range must cover it for accurate square-wave response.

Elecvora expert review

Our verdict

The FNIRSI P6100 is a straightforward single-channel probe that covers the everyday needs of most bench work. Its 100 MHz bandwidth and sub-3.5 ns rise time make it a sensible spare or starter probe for standard 1MΩ scopes.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • 100 MHz bandwidth suits a wide range of measurements
  • Switchable 1X/10X attenuation adds flexibility
  • Adjustable compensation from 10pF to 30pF
  • Long 1.2 m cable for flexible positioning
  • Light 133 g body is comfortable in hand

Cons

  • Single channel only, so two probes are needed for dual-channel work
  • Compensation range is limited to scopes within 10pF to 30pF
  • No dedicated carry case listed beyond the accessory kit

Best for

Hobbyists and technicians who need a reliable single-channel probe for a 1MΩ oscilloscope

Not ideal for

Dual-channel measurements or scopes with input capacitance outside the 10pF to 30pF range

Specifications

Item TypeOscilloscope Probe
No. of ChannelsSingle
Input Resistance1MΩ
Bandwidth100
Cable Length1.2 Meter
Channelsingle
Rise Time<3.5 nsec
Length (mm)260
Width (mm)160
Weight (g)133
Colorblack+grey
Shipping Weight0.133 kg
Shipping Dimensions26 × 16 × 1 cm

What's in the box

  • 1 x FNIRSI P6100 Oscilloscope Probe
  • 1 x Accessory Kit

Frequently Asked Questions

What is the bandwidth of the P6100 probe?
The probe is rated at 100 MHz bandwidth, with a rise time under 3.5 ns. That makes it suitable for a broad range of digital and analog measurements.
Can I use it with any oscilloscope?
It is designed for oscilloscopes with a standard 1MΩ input. The adjustable compensation range of 10pF to 30pF must cover your scope's input capacitance for accurate results.
Does the probe need a battery or external power?
No. It is a passive probe and draws no power of its own; it simply connects to the scope's input.
What does the 1X/10X switch do?
It selects the attenuation ratio. In 10X mode the signal is divided by ten before reaching the scope, which is the usual setting for general troubleshooting.
What is included with the probe?
The package contains one FNIRSI P6100 oscilloscope probe and one accessory kit.
How should I store and care for the probe?
Coil the 1.2 m cable loosely rather than bending it sharply, keep the tip and ground clip clean, and store the probe within the stated operating range of -10℃ to +50℃.

Overview

The FNIRSI P6100 is a single-channel oscilloscope probe designed for accurate signal measurement on standard scopes. It combines 100 MHz bandwidth with switchable 1X/10X attenuation, so the same probe can handle low-level signals and higher-frequency work without swapping hardware. The 1MΩ input resistance and sub-3.5 ns rise time help keep readings clean, while the 1.2 m cable gives you room to reach into a chassis or across a bench.

Key Features

  • Single-channel probe with 100 MHz bandwidth
  • Selectable 1X and 10X attenuation
  • Rise time under 3.5 ns for fast edge response
  • 1MΩ input resistance
  • Adjustable compensation from 10pF to 30pF
  • 1.2 m cable, black and grey body

Specifications Explained

Bandwidth and rise time

100 MHz bandwidth sets the range of frequencies the probe can pass with reasonable accuracy. The under-3.5 ns rise time is the figure that matters when you look at sharp digital edges: a faster rise time means the probe itself adds less rounding to the waveform you see on screen.

1X and 10X attenuation

The switch lets you choose between 1X for direct, lower-level signals and 10X for higher-voltage or higher-frequency work. In 10X mode the probe divides the signal by ten before it reaches the scope, which is the usual setting for general troubleshooting.

Input resistance and compensation

The 1MΩ input resistance matches the input impedance found on most oscilloscopes. The 10pF to 30pF compensation range is adjustable so you can trim the probe to your scope's input capacitance and keep square waves looking square.

Physical details

The probe measures 260 mm long and 160 mm wide and weighs 133 g. The 1.2 m cable is long enough for comfortable bench use without adding unnecessary slack.

Compatibility and Requirements

The P6100 is intended for oscilloscopes with a standard 1MΩ input. Compensation is adjustable between 10pF and 30pF, so it can be matched to scopes whose input capacitance falls in that window. It is a passive probe and needs no separate power source.

Typical Uses

  • Checking digital and analog waveforms during repair work
  • Diagnosing signal integrity on hobby and prototype boards
  • Student lab exercises and learning oscilloscope basics
  • Keeping a spare probe ready on the bench

What's in the Box

One FNIRSI P6100 oscilloscope probe and one accessory kit.

Quick specs

Item Type
Oscilloscope Probe
No. of Channels
Single
Input Resistance
1MΩ
Bandwidth
100
Cable Length
1.2 Meter
Channel
single
See all specifications

More from FNIRSI

View all →

Related Products

View all →