
1 / 4 · Click to enlarge
AI Summary
A 65A x4 4in1 ESC for FPV quads, rated for 3-6S LiPo with 80A peaks per channel. AM32 firmware and 48-96KHz dynamic PWM give fast, tunable motor response in a 15g board.
Key Highlights
- 65A continuous and 80A peak on each of four channels
- 3-6S LiPo input range for flexible build voltage
- AM32 XROTOR65 F421 firmware with dynamic 48-96KHz PWM
- 32-bit ARM F4 processor for fast throttle response
- Integrated 5V 0.6A BEC and onboard voltmeter
- Compact 52 x 42mm board weighing about 15g
Ideal For
- FPV racing pilots building compact 5-inch quads
- Freestyle pilots upgrading to an AM32-based 4in1 ESC
- Builders working with 3-6S LiPo multirotor setups
- Hobbyists who want a small, light 4in1 ESC board
- Pilots who tune motor response through a web interface
Buying Tip
Check that your motors and props stay within 65A continuous per channel, and remember the 5V BEC only supplies 0.6A, so power heavier accessories separately.
Elecvora expert review
Our verdict
A compact, well-specified 4in1 ESC that brings AM32 tuning and dynamic PWM to 3-6S FPV builds. The 65A per-channel rating and 15g weight make it a sensible choice for performance quads.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- 65A continuous and 80A peak per channel
- AM32 firmware with web-based tuning
- Dynamic 48-96KHz PWM range
- Light 15g board with compact footprint
- Onboard 5V BEC and voltmeter
Cons
- Requires soldering for motor and power connections
- 5V BEC limited to 0.6A
- No package accessories beyond the ESC listed
Best for
FPV pilots building or upgrading 3-6S multirotors
Not ideal for
Builds drawing more than 65A continuous per motor channel
Specifications
| Item Type | Electronic Speed Controller |
|---|---|
| Constant Current (A) | 65Ax4 |
| Input wires | 12AWG-130mm (Red/Black) |
| Continuous Discharge Current (A) | 60A x 4 |
| Peak Current (A) | 80A x 4 |
| Input Voltage | 3-6S LiPo |
| BEC Output | 5V @ 0.6A |
| Firmware | AM32 XROTOR65 F421 |
| PWM frequency | 48KHz - 96KHz Dynamic |
| Length (mm) | 52 |
| Width (mm) | 42 |
| Weight (g) | 15 |
| Shipping Weight | 0.087 kg |
| Shipping Dimensions | 14 × 9 × 4 cm |
What's in the box
- 1 x Hobbywing XRotor FPV G2 ESC 4in1 65A - NEW Version
Frequently Asked Questions
What battery voltage does this ESC support?
How much current can each channel handle?
What firmware does it run?
Can I power accessories from the BEC?
What is included in the box?
Do I need to solder to install it?
Overview
The Hobbywing XRotor FPV G2 65A is a 4in1 electronic speed controller designed for FPV multirotor builds. It packs four independent 65A channels onto a single board measuring about 52 x 42mm and weighing roughly 15g, so it fits neatly into compact frames without adding bulk. Power input is handled through 12AWG red and black wires, and the board accepts 3-6S LiPo packs.
At the heart of the ESC is a 32-bit ARM F4 processor running AM32 XROTOR65 F421 firmware. This combination supports dynamic PWM frequencies from 48KHz to 96KHz and is ready for web-based parameter tuning, giving builders a modern platform for setting up motor behaviour.
Key Features
- Four 65A channels: 65A continuous and 80A peak per motor output.
- 3-6S LiPo input: works across common FPV pack voltages.
- AM32 firmware: XROTOR65 F421 build with web parameter tuning.
- Dynamic PWM: switching range of 48KHz to 96KHz.
- 32-bit ARM F4 MCU: fast processing for responsive throttle control.
- 5V 0.6A BEC: onboard power for low-draw accessories.
- Integrated voltmeter: check pack voltage on the bench.
Specifications Explained
The 65A continuous rating per channel tells you how much current each motor can draw steadily, while the 80A peak figure covers short bursts. The 3-6S input range means the ESC is suited to builds running anything from 3S to 6S LiPo packs. The 5V 0.6A BEC is a modest supply, so plan to power only light accessories from it. Dynamic PWM between 48KHz and 96KHz lets the firmware adjust switching behaviour, and the AM32 platform is tunable through a web interface. The 12AWG input wires are sized for the main power lead, and the 52 x 42mm footprint keeps wiring compact.
Compatibility and Requirements
This ESC requires a 3-6S LiPo power source and a flight controller capable of driving it through standard ESC protocols. Because it is an AM32-based board, setup and tuning are done through the AM32 web interface. A soldering iron is needed to attach motors and the main power lead. Always confirm your build's current draw stays within the 65A continuous and 80A peak per-channel ratings.
Typical Uses
This 4in1 ESC suits FPV quad builds where four motors need compact, individually rated control. It is a natural fit for performance-oriented freestyle and racing builds, and for pilots upgrading an existing quad to an AM32-based board with dynamic PWM. Its small size also makes it useful where frame space is limited.
What's in the Box
- 1 x Hobbywing XRotor FPV G2 ESC 4in1 65A - NEW Version

Quick specs
- Item Type
- Electronic Speed Controller
- Constant Current (A)
- 65Ax4
- Input wires
- 12AWG-130mm (Red/Black)
- Continuous Discharge Current (A)
- 60A x 4
- Peak Current (A)
- 80A x 4
- Input Voltage
- 3-6S LiPo



















