
1 / 3 · Click to enlarge
AI Summary
A 24V DC detection module that signals your 3D printer to stop and lift the Z-axis when mains power fails, protecting the model from nozzle damage. It keeps the board powered long enough to raise Z by roughly 20-200 mm, then lets you resume from the LCD.
Key Highlights
- Detects AC power loss and signals the printer motherboard
- Uses stored energy to lift the Z-axis after shutdown
- Raises Z by approximately 20 mm to 200 mm
- 24V DC input for compatible printer setups
- Compact 65 x 60 mm module weighing 43 g
- Resume printing from a 12864 or 2004 LCD screen
Ideal For
- Makers running long unattended 3D prints
- Users in areas with unstable mains power
- Printers running Marlin 2.0 with a 12864 or 2004 LCD
- 24V DC printer builds needing print protection
- Workshops wanting a low-cost alternative to a full UPS
Buying Tip
Confirm your printer uses a 24V DC power supply and Marlin 2.0 with a 12864 or 2004 LCD before ordering, since the module will not work with 12V systems or MKS TFT screens.
Elecvora expert review
Our verdict
A focused, affordable module that solves a real problem: losing a long print to a sudden power cut. It does one job well, provided your printer meets the voltage and firmware requirements.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Protects prints by lifting the Z-axis after power loss
- Simple signal-based shutdown sequence
- Small 65 x 60 mm footprint and light 43 g weight
- Lets you resume printing from a compatible LCD
Cons
- Only works with 24V DC power
- Requires Marlin 2.0 and a 12864 or 2004 LCD
- Not compatible with most MKS Robin boards or MKS TFT screens
Best for
Makers with 24V Marlin 2.0 printers who want basic power-loss protection
Not ideal for
Printers running 12V systems, MKS TFT screens or unsupported Robin boards
Specifications
| Item Type | Module |
|---|---|
| Material | Plastic, Metal |
| Length (mm) | 65 |
| Width (mm) | 60 |
| Model No. / Name | UPS24V |
| Weight (g) | 43 |
| Size (mm) | 65x60 |
| Shipping Weight | 0.069 kg |
| Shipping Dimensions | 17 × 13 × 2 cm |
What's in the box
- 1 x MakersBase MKS UPS24V module
- 2 x power cables
- 1 x 3-pin motherboard cable
Frequently Asked Questions
What does the MKS UPS24V actually do?
How far does it lift the Z-axis?
Can I use it with a 12V printer?
Which firmware and screens are supported?
How do I resume printing after power returns?
What comes in the package?
Overview
The Makerbase MKS UPS24V is a small detection and backup module for 3D printers. Its job is simple: when the AC mains supply disappears, it alerts the motherboard and keeps the electronics running long enough to move the Z-axis away from the printed part. Without this, a power cut mid-print can leave the hot nozzle resting against the model, ruining the surface and sometimes the print itself.
The module measures 65 x 60 mm and weighs 43 g, so it fits easily into most electronics enclosures and adds very little load.
Key Features
- Power-loss detection: monitors the external AC supply and sends a signal to the motherboard when it drops.
- Z-axis lift: the energy held in the module and PSU lets the printer raise Z by roughly 20 mm to 200 mm before shutting down.
- Safe shutdown sequence: the firmware stops printing and turns off the hotend and hotbed before lifting the axis.
- Print resume: once power is back, printing can be restarted from a 12864 or 2004 LCD screen.
- Multiple output ports: supply power to more than one device at the same time.
Specifications Explained
24V DC operation means the module is designed for printers running a 24V power system. It is not a 12V part, so check your PSU output before buying. Size and weight are modest at 65 x 60 mm and 43 g, which keeps installation simple. The plastic and metal construction houses the detection circuitry and connection points. Output ports allow several devices to draw power through the module, which is handy when the board and accessories need to stay alive during the lift.
Compatibility and Requirements
The MKS UPS24V works with motherboards running Marlin 2.0 firmware and a 12864 or 2004 LCD screen. It does not currently support the MKS Robin series, with the exception of the Robin E3 and E3D, and it does not support MKS TFT screens. The module detects an external AC power supply, and the 24V version must only be used with DC 24V power.
Typical Uses
This module suits anyone running long prints who wants a basic safety net against sudden power cuts. It is useful in workshops or homes where the mains supply is unreliable, and for overnight or multi-hour jobs where losing a print is costly. It is also a sensible upgrade for printers that already use Marlin 2.0 and a compatible LCD.
What's in the Box
- 1 x MakersBase MKS UPS24V module
- 2 x power cables
- 1 x 3-pin motherboard cable

Quick specs
- Item Type
- Module
- Material
- Plastic, Metal
- Length (mm)
- 65
- Width (mm)
- 60
- Model No. / Name
- UPS24V
- Weight (g)
- 43



















