
At a glance
Made by Seeed Studio, this light sensor modules is a good fit for makers, students and electronics hobbyists. Main specs: model no. / name Light Sensor; operating current (ma) 0.5 to 3; length (mm) 20.
Key Highlights
- Model No. / Name: Light Sensor
- Operating Current (mA): 0.5 to 3
- Length (mm): 20
Ideal For
- Arduino, ESP32 and Raspberry Pi projects
- School and college lab work
- Prototypes and test rigs
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Model No. / Name | Light Sensor |
|---|---|
| Operating Current (mA) | 0.5 to 3 |
| Peak Response wavelength(nM) | 540 nm |
| Length (mm) | 20 |
| Width (mm) | 20 |
| Mounting Hole Diameter (mm) | 2 |
| Weight (g) | 4 |
| Response Time (uS) | 30 |
| Shipping Weight | 0.005 kg |
| Shipping Dimensions | 6.8 × 4.5 × 1.8 cm |
Overview
The Seeed Studio Grove Light Sensor, made by Seeed Studio, is listed in our light sensor modules range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Model No. / Name: Light Sensor
- Operating Current (mA): 0.5 to 3 (your supply must deliver at least this much current)
- Peak Response wavelength(nM): 540 nm (measure your mounting space before ordering)
- Length (mm): 20 (measure your mounting space before ordering)
- Width (mm): 20 (measure your mounting space before ordering)
- Mounting Hole Diameter (mm): 2
- Weight (g): 4 (important for drones, RC models and anything you carry)
- Response Time (uS): 30
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
Need a device to sense light? We have the Grove – Light Sensor v1.2 for you. Now you can measure light levels with higher reliability and sensibility. It is an updated version of Grove - Light Sensor 1.0. You can use it as a light-controlled switch i.e. switch off lights during day time and switch on lights during night time.
The resistance of light sensor, also known as the Light Dependent Resistor (LDR) decreases when the ambient light intensity increases. However, the change in resistance due to ambient light is not linear; in low-light conditions, small changes in luminescence cause relatively large changes in resistance (or output voltage), but in well-lit conditions, changes in luminescence cause only small changes in resistance.
A dual OP-AMP chip LM358 on board produces voltage corresponding to the intensity of light (i.e. based on the resistance value). The output signal is an analog value. The brighter the light is, the larger the value will be. The output electrical signals can be converted to different ranges (It depends on the Analog-to-Digital-Converter on your controller board. For example, it can output 0-255 for an 8-bit ADC). It integrates a high-sensitive and reliable phototriode GL5528. Just like other grove modules, you can interface this sensor with Grove port which can save a lot of work in the wiring.
For all Grove users (especially beginners), Seeed Studio provides guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before using the product. This is a suitable product for not only Grove users but also all electronic enthusiasts. So, why wait? Buy now!
Warning: The light sensor value only reflects an approximated trend of light intensity, it DOES NOT represent the exact Lumen count.Hardware Overview:
- Grove port to connect the cable
- Phototriode (GL5528) as a photodetector
Features:
- Analog value output
- High reliability and sensibility
- Small footprint
- Recognizes a wide spectrum
- Easy to use
Useful Links:
TutorialProject Links:
Package Includes:
1 x Seeed Studio Grove Light SensorQuick specs
- Model No. / Name
- Light Sensor
- Operating Current (mA)
- 0.5 to 3
- Peak Response wavelength(nM)
- 540 nm
- Length (mm)
- 20
- Width (mm)
- 20
- Mounting Hole Diameter (mm)
- 2





















