Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact HX711 breakout that lets your microcontroller read a four-wire load cell and measure weight with simple calibration. It runs from 2.7V to 5V with selectable 10SPS or 80SPS output and a two-wire interface.

Key Highlights

  • HX711 amplifier IC for reading four-wire load cells
  • Wide 2.7V to 5V operating voltage range
  • Low current draw of under 1.5mA
  • Selectable 10SPS or 80SPS output data rate
  • Separated analog and digital supplies with filtering
  • Compact PCB measuring 30.48 x 22.86mm

Ideal For

  • Makers building DIY digital scales
  • Students learning about load cells and amplifiers
  • Electronics hobbyists adding weight sensing to projects
  • Engineers prototyping process-control rigs
  • Anyone needing a compact HX711 breakout board

Buying Tip

Confirm your load cell's wire colours and bridge wiring before soldering, since colour coding can vary between cells.

Elecvora expert review

Our verdict

A tidy, well-filtered HX711 breakout that gives you the core of a weighing project with minimal fuss. It is a sensible pick for hobbyists and students who want reliable load cell readings without building the amplifier circuit themselves.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Separated analog and digital supplies with filtering
  • Wide 2.7V to 5V operating range
  • Selectable 10SPS or 80SPS output rate
  • Simple two-wire interface works with common GPIO pins
  • Compact board size

Cons

  • Requires soldering and a separate microcontroller
  • No load cell included
  • Calibration is needed before readings are meaningful

Best for

DIY scales and weight-sensing projects

Not ideal for

Plug-and-play weighing out of the box

Specifications

Model No. / NameHX711
Voltage Rating (V)2.7 to 5
AC Current(A)< 1.5
PCB Size ( L x W ) mm30.48 x 22.86
Data Transfer Rate10SPS or 80SPS
Shipping Weight0.003 kg
Shipping Dimensions5 × 5 × 2 cm

What's in the box

  • 1 x SmartElex Load Cell Amplifier - HX711

Frequently Asked Questions

What is the HX711 used for?
It amplifies the small signal from a load cell so a microcontroller can read it and calculate weight. The board is commonly used in DIY scales and force-sensing projects.
Which microcontrollers can I use?
The two-wire clock and data interface works with any microcontroller GPIO pins, and many libraries exist to help read the data.
What voltage does the board need?
It operates from 2.7V to 5V and draws under 1.5mA, so it can share a supply with common 3.3V or 5V boards.
How do I connect a load cell?
Load cells use a four-wire Wheatstone bridge connection, usually colour-coded red, black, white and green, with an optional yellow shield wire on some cells. Colour coding can vary, so check your cell's documentation.
What data rate can I select?
You can choose between 10SPS and 80SPS output, depending on how quickly you need readings.
What is included with the board?
The package contains one SmartElex Load Cell Amplifier - HX711 board. A load cell and microcontroller are not included.

Overview

The SmartElex Load Cell Amplifier is a small breakout board built around the HX711 IC, made for turning the tiny resistance changes inside a load cell into a signal your microcontroller can read. Connect the board to your controller, calibrate against known weights, and you have the core of a digital scale or a weight-based sensing project.

This version separates the analog and digital supply rails and adds a 3.3uH inductor plus a 0.1uF filter capacitor on the digital supply, which helps keep the digital side from disturbing the sensitive analog measurement.

Key Features

  • HX711 amplifier IC on a ready-to-use breakout board
  • Two-wire clock and data interface that works with ordinary GPIO pins
  • 2.7V to 5V operating voltage
  • Current consumption below 1.5mA
  • Selectable 10SPS or 80SPS output data rate
  • Simultaneous 50Hz and 60Hz supply rejection
  • Separated analog and digital supplies with inductor and capacitor filtering

Specifications Explained

Voltage and current

A 2.7V to 5V range means the board can share a supply with common 3.3V and 5V microcontroller boards. Drawing under 1.5mA, it adds very little load to your power rail.

Output data rate

You can select 10SPS for slower, steadier readings or 80SPS when you want updates to arrive more often. Choose the rate that matches how quickly your project needs weight data.

PCB size

At 30.48 x 22.86mm, the board is small enough to fit inside enclosures and project boxes while leaving room for the load cell wiring.

Noise rejection

Simultaneous 50Hz and 60Hz rejection helps reduce interference from mains-powered equipment, which is useful when readings are taken near lighting or machinery.

Compatibility and Requirements

The HX711 uses a two-wire interface for clock and data, and any microcontroller GPIO pins should work. Numerous libraries have been written to help read data from the chip. Load cells connect using a four-wire Wheatstone bridge configuration, commonly colour-coded red, black, white and green, with a yellow shield wire on some cells. Colour coding can vary between load cells, so check your cell's documentation. You will need a microcontroller and a suitable load cell, which are not included.

Typical Uses

  • DIY digital scales and weighing platforms
  • Process control and force monitoring
  • Simple presence or load detection
  • Classroom and hobby electronics projects

What's in the Box

One SmartElex Load Cell Amplifier - HX711 board.

Quick specs

Model No. / Name
HX711
Voltage Rating (V)
2.7 to 5
AC Current(A)
< 1.5
PCB Size ( L x W ) mm
30.48 x 22.86
Data Transfer Rate
10SPS or 80SPS
Shipping Weight
0.003 kg
See all specifications