
1 / 3 · Click to enlarge
AI Summary
An 8-channel IR reflectance sensor bar with independent analog and digital outputs plus a sensitivity trimmer on every channel. It gives line-following robots a ready-made, evenly spaced sensing array that connects straight to a microcontroller.
Key Highlights
- Eight IR emitter and phototransistor pairs on one carrier board
- Independent analog and digital output for every channel
- Per-sensor potentiometer for individual sensitivity adjustment
- Sensors spaced 15 mm apart along a 126 x 26 mm PCB
- 4.5 to 5.0 V supply with roughly 0.15 A current draw
- 3 mm mounting holes for simple chassis attachment
Ideal For
- Students building their first line-following robot
- Makers upgrading from a 2- or 3-sensor bar to 8-channel sensing
- Robotics clubs working on grid navigation and junction detection
- Hobbyists who want analog and digital outputs on the same board
- Educators demonstrating reflectance sensing in the classroom
Buying Tip
Check that your chassis can hold the board about 3 mm above the floor, since the stated detection distance is very short.
Elecvora expert review
Our verdict
A practical eight-channel sensor bar that gives line-following robots good resolution and the flexibility of both analog and digital outputs. The per-channel trimmers are the feature that makes it worth choosing over a fixed-threshold array.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Eight evenly spaced channels for finer line position data
- Analog and digital output on every channel
- Individual sensitivity potentiometer per sensor
- Simple 3 mm mounting holes and light 16 g board
Cons
- Detection distance is only about 3 mm, so mounting height is critical
- No mounting hardware or cables included
- Requires an external 4.5 to 5.0 V supply at roughly 0.15 A
Best for
Line-following and grid-navigating robots built around a microcontroller
Not ideal for
Projects that need long-range or non-contact distance sensing
Specifications
| Model No. / Name | RLS08 |
|---|---|
| Voltage Rating (V) | 4.5 to 5.0 |
| Output Format | 8 Analog and Digital Voltage |
| Detection Distance (mm) | 3 |
| PCB Size ( L x W ) mm | 126 x 26 |
| Additional Specs. | Distance between two IR sensor (mm): 15 |
| Supply Current | 0.15 A |
| Max. Sensing Distance (cm) | 0.6 cm |
| Length (mm) | 120 |
| Weight (g) | 16 |
| Width (mm) | 26 |
| Mounting Hole Diameter (mm) | 3 |
| Shipping Weight | 0.105 kg |
| Shipping Dimensions | 9 × 4 × 2 cm |
What's in the box
- 1 x SmartElex RLS-08 Analog & Digital Line Sensor Array
Frequently Asked Questions
How many sensors does the RLS-08 have?
What outputs does each channel provide?
What voltage does the board need?
How close must the sensor be to the surface?
Can I connect it directly to a microcontroller?
What is included with the sensor array?
Overview
The SmartElex RLS-08 is a carrier board for eight infrared emitter and receiver pairs, arranged in a straight row for line sensing. Each pair works as a reflectance sensor: the emitter bounces IR light off the surface below, and the phototransistor converts the reflected light into a voltage. Because the eight channels are evenly spaced at 15 mm intervals, the board reports the position of a line across its full width rather than a single on/off point.
Every channel exposes both an analog voltage output and a digital output, and each has its own potentiometer so you can tune sensitivity channel by channel. That makes the RLS-08 useful both for quick digital line detection and for analog readings where you want a graded response.
Key Features
- Eight sensing channels: 8 IR emitter/receiver pairs give finer line resolution than a two- or three-sensor bar.
- Dual outputs: analog and digital voltage available from each channel.
- Individual trimmers: a potentiometer per sensor lets you balance channels against different surfaces and lighting.
- Even spacing: 15 mm between adjacent IR sensors for consistent coverage.
- Compact board: 126 x 26 mm PCB with 3 mm mounting holes.
- Low mass: approximately 16 g, so it adds little weight to a small chassis.
Specifications Explained
Voltage and current
The board is rated for 4.5 to 5.0 V and draws about 0.15 A. Plan your supply and wiring around that current figure, and keep the input inside the stated range.
Detection distance
The stated detection distance is 3 mm, with a maximum sensing distance of 0.6 cm. In practice this means the sensor bar should sit close to the floor, which is typical for line-following robots.
Output format
Each of the eight channels provides an analog voltage and a digital voltage. The analog output gives you a continuous reading of reflected IR, while the digital output gives a simple threshold result set by that channel's potentiometer.
Physical size
The PCB measures 126 x 26 mm, with a 120 mm length and 26 mm width listed for the board body. Mounting holes are 3 mm in diameter, matching common M3 hardware.
Compatibility and Requirements
The RLS-08 is designed to connect directly to microcontroller digital and analog inputs. You will need a 4.5 to 5.0 V supply capable of around 0.15 A and a robot chassis or bracket that can hold the board close to the ground. Mounting hardware for the 3 mm holes is not included.
Typical Uses
- Line-following robots that need to track a line position across a wide sensor bar
- Grid-navigating robots that read junctions and crossings
- General-purpose proximity or reflectance experiments
- Classroom and hobby projects teaching analog versus digital sensing
What's in the Box
1 x SmartElex RLS-08 Analog & Digital Line Sensor Array.

Quick specs
- Model No. / Name
- RLS08
- Voltage Rating (V)
- 4.5 to 5.0
- Output Format
- 8 Analog and Digital Voltage
- Detection Distance (mm)
- 3
- PCB Size ( L x W ) mm
- 126 x 26
- Additional Specs.
- Distance between two IR sensor (mm): 15




















