Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 2.13 inch E-Ink HAT for Raspberry Pi that shows red, black and white content at 212x104 and keeps the last image on screen without power. It refreshes over SPI and draws almost nothing in standby, making it ideal for static labels and status panels.

Key Highlights

  • 212x104 three-colour panel showing red, black and white
  • Holds the last displayed image with power removed
  • SPI interface with 3-wire and 4-wire support
  • Onboard voltage translator for 3.3V and 5V boards
  • Wide viewing angle beyond 170 degrees
  • Solder pads for Arduino, STM32 and other controllers

Ideal For

  • Raspberry Pi hobbyists building low-power status displays
  • Makers creating shelf labels and signage
  • Students learning SPI and E-Ink programming
  • Engineers prototyping battery-friendly information panels
  • Arduino and STM32 developers adding a static screen

Buying Tip

Check that your project can tolerate a roughly 15-second full refresh and periodic updates before choosing this three-colour panel.

Elecvora expert review

Our verdict

A tidy, well-documented E-Ink HAT that adds a readable three-colour panel to a Raspberry Pi with minimal wiring. Its value comes from holding an image without power, not from speed or colour depth.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Very low standby power once an image is written
  • Three colours allow simple emphasis and alerts
  • Works with 3.3V and 5V boards via onboard translator
  • Wide viewing angle and good readability in daylight

Cons

  • Full refresh takes about 15 seconds
  • Only two grey levels, so no smooth shading
  • Raspberry Pi not included

Best for

Static status panels and labels on Raspberry Pi projects

Not ideal for

Projects needing fast animation or full-colour graphics

Specifications

Model No. / NameDisplay HAT
Display Size (Inch)2.13
Display Resolution (pixel)212 × 104
Display ColorRed, Black and White
Operating Voltage (V)3.3
Outline dimension (mm)65 × 30.2
Dot Pitch0.229 × 0.228
Grey level2
Viewing Angle (Deg.)>170°
Interface3-wire SPI, 4-wire SPI
Full Refresh Time (s)15
Refresh Power26.4mW(typ.)
Standby Power (mW)<0.017
Dimensions (L x W x H) mm65 x 31 x 8
Weight (g)20
Shipping Weight0.022 kg
Shipping Dimensions9 × 7 × 4 cm

What's in the box

  • 1 x Waveshare 2.13 inch E-Ink Paper display HAT for Raspberry Pi, Three-Color
  • 1 x Interfacing cable
  • 1 x Nut, bolt and spacer set

Frequently Asked Questions

Does the screen keep its image when power is removed?
Yes. The E-Ink panel holds the last displayed content without power, and current is only needed when refreshing.
Which Raspberry Pi models are supported?
The HAT is listed for Raspberry Pi Zero, Zero W, Zero WH, 2B, 3B and 3B+, with development resources and a manual included.
Can I use it with an Arduino or STM32 board?
Yes. Preserved solder pads expose the SPI interface, and the resources include examples for Arduino and STM32.
What voltage does it need?
The display operates at 3.3V, and the onboard translator makes it compatible with both 3.3V and 5V microcontrollers.
How long does a refresh take?
A full refresh takes about 15 seconds, so the display suits periodic updates rather than fast-changing content.
Is a Raspberry Pi included?
No. The package contains the display HAT, an interfacing cable and a nut, bolt and spacer set only.

Overview

The Waveshare 2.13 inch E-Ink Paper display HAT gives a Raspberry Pi a compact electronic paper screen that shows red, black and white content at 212x104 pixels. Because the panel has no backlight and only needs power while it refreshes, the last image stays visible after the supply is removed. That makes it a practical choice for information that changes occasionally rather than continuously.

The board measures roughly 65 x 31 x 8 mm and weighs about 20 g, so it sits neatly on top of a Pi without adding bulk. An onboard voltage translator means the same HAT can be used with 3.3V and 5V microcontroller boards.

Key Features

  • Three-colour display: red, black and white for simple emphasis and alerts
  • 212x104 resolution with a dot pitch of 0.229 x 0.228 mm
  • SPI interface supporting 3-wire and 4-wire modes
  • Full refresh time of about 15 seconds
  • Refresh power around 26.4 mW typical, standby below 0.017 mW
  • Viewing angle greater than 170 degrees, readable in bright light
  • Exposed solder pads for SPI connection to Arduino, Nucleo and STM32 boards

Specifications Explained

The 2.13 inch diagonal and 212x104 pixel grid suit short lines of text, icons and simple status layouts rather than detailed images. Two grey levels are available, so shading is limited; the red channel is best used for highlights such as warnings or headings.

Refresh takes about 15 seconds, which is normal for this class of panel. Plan your project around periodic updates rather than animation. The very low standby figure is the main advantage: once an image is written, the display holds it without continuous power.

The 3.3V operating voltage and onboard translator cover both 3.3V and 5V logic, and the SPI pins are labelled VCC, GND, DIN, CLK, CS, DC, RST and BUSY for straightforward wiring.

Compatibility and Requirements

The HAT is designed for Raspberry Pi Zero, Zero W, Zero WH, 2B, 3B and 3B+ boards, and development resources include examples for Raspberry Pi, Arduino and STM32. Other controllers can be connected through the preserved SPI solder pads. A Raspberry Pi is not included, so you will need your own board plus the supplied interfacing cable.

Typical Uses

  • Status and sensor readouts that update every few minutes
  • Labels, name tags and shelf signage
  • Low-power dashboards and weather panels
  • Calendar or task displays that refresh periodically
  • Learning projects exploring SPI and E-Ink control

What's in the Box

  • 1 x Waveshare 2.13 inch E-Ink Paper display HAT, three-colour
  • 1 x Interfacing cable
  • 1 x Nut, bolt and spacer set

Quick specs

Model No. / Name
Display HAT
Display Size (Inch)
2.13
Display Resolution (pixel)
212 × 104
Display Color
Red, Black and White
Operating Voltage (V)
3.3
Outline dimension (mm)
65 × 30.2
See all specifications

More from WAVESHARE

View all →

Related Products

View all →